Best Clamp Meters for Electronics: 7 UNI-T, OWON, Fluke, Klein and Hantek Picks Compared (Buying Guide)

⚠️ Affiliate Disclosure: This post contains Amazon affiliate links. If you purchase through our links, we may earn a small commission at no extra cost to you. Every product below was checked against its live Amazon listing before publishing. Prices change often, so we don’t list them here. Tap any Buy Here button to see the current price on Amazon.
Test Gear Buying Guide

πŸ”Œ Best Clamp Meters for Electronics

Measure current without cutting a single wire. Here are 7 AC/DC clamp meters and a scope current clamp, from mini milliamp-resolution clamps for ESP32 boards to Fluke meters for solar, battery and motor wiring.

βœ… 7 Clamps Compared βœ… Verified Amazon ASINs βœ… DC Current Focus βœ… Honest Pros & Cons

A multimeter measures current by breaking the circuit and routing it through the meter. That’s fine on a breadboard, but awkward on a finished build where an ESP32 controller drives an LED strip, a pump, a motor or a battery pack. A clamp meter wraps its jaw around one wire and reads the current from the magnetic field, so you can check a running project without unplugging or cutting anything.

The catch for electronics work is DC current. Many cheap clamps only read AC, which is useless for 5 V and 12 V projects. Every meter in this guide reads DC, and we’ve ranked them on what matters at a maker bench: the smallest current range, its resolution, jaw size and extras like Bluetooth logging or an oscilloscope output.

πŸ’‘ Before you buy: A clamp meter is great for tens of milliamps and up: Wi-Fi transmit current, LED strips, motors, chargers and solar feeds. It cannot read ESP32 deep-sleep current in the microamp range. For that, use a USB power meter or current profiler in series. Also make sure the meter says AC/DC current, not just AC/DC voltage: plenty of listings mix the two.

⚑ Quick Comparison: All 7 Clamp Meters

ClampDC CurrentSmallest RangeJawBest ForBuy
πŸ₯‡ UNI-T UT210EUp to 100 A2 A (1 mA steps)17 mmBest for ESP32 ProjectsBuy Here β†’
πŸ† Fluke 325Up to 400 A40 A30 mm conductorBest All-Round Pro MeterBuy Here β†’
πŸ“± OWON CM2100BUp to 100 A2 A (1 mA steps)17 mmBest Bluetooth LoggingBuy Here β†’
πŸ”¦ Klein CL81010 mA to 600 AAuto-ranging36 mmBest Feature ValueBuy Here β†’
🧲 Fluke 365Up to 200 A0.1 A steps18 mm detachableBest for Tight EnclosuresBuy Here β†’
πŸ’Ž Fluke 376 FCUp to 999.9 A0.1 A steps34 mm + iFlexBest for Solar and Battery BanksBuy Here β†’
πŸ“ˆ Hantek CC-65020 mA to 650 AScope output30 mm conductorBest for OscilloscopesBuy Here β†’

Specs come from the manufacturers and the live Amazon listings. Star scores below are our ratings.

πŸ” What Matters in a Clamp Meter for Electronics

πŸ”‹

True DC Current

DC clamps use a Hall-effect sensor. AC-only clamps read zero on a 5 V or 12 V wire, so check the current spec, not the voltage spec.

πŸ”¬

Low Range and Resolution

A 2 A range with 1 mA steps shows an ESP32’s Wi-Fi current. A 40 A or 400 A range only shows tenths of an amp or more.

🎯

DC Zero Button

Hall sensors drift and pick up the Earth’s field. A zero or REL button before each reading makes low-current DC readings usable.

βœ‹

Jaw Size

Small jaws slip between wires in a crowded enclosure; big jaws or flexible probes take thick battery and solar cables.

πŸ›‘οΈ

Safety Rating

If your ESP32 projects touch mains wiring, pick a meter with a real CAT III or CAT IV rating from a known brand.

πŸ† Detailed Reviews: The Top Two

πŸ₯‡ BEST FOR ESP32 PROJECTS

UNI-T UT210E Mini Clamp Meter

⭐ 4.6/5 · Our Rating · The Maker Favourite
2 A
LOWEST RANGE
1 mA
RESOLUTION
100 A
AC/DC MAX
17 mm
JAW
Buy on Amazon β†’
UNI-T UT210E mini AC DC clamp meter

The UT210E is the clamp meter electronics hobbyists recommend most, because it has something the big-name electrician’s clamps lack: a 2 A DC range with 1 mA resolution. That’s enough to watch an ESP32 jump from idle to a Wi-Fi transmit burst, see how much an LED strip or servo really draws, or confirm a 12 V pump is within its driver’s limit. It also has 20 A and 100 A ranges, True RMS, a 17 mm jaw that fits between wires on a crowded board, plus the usual voltage, resistance, capacitance and continuity functions with test leads. Press the zero button before each DC reading, as the 2 A range is sensitive to nearby magnetic fields.

βœ… Pros
  • 1 mA DC resolution
  • Small jaw for tight wiring
  • Pocket sized
  • Excellent value
❌ Cons
  • 2000 count display
  • Needs zeroing for low DC
  • Not for serious mains work
🎯 Verdict: The best first clamp meter for ESP32, LED and motor projects. Nothing else this affordable reads milliamps of DC.

πŸ‘‰ Check Price on Amazon β†’

πŸ† BEST ALL-ROUND PRO METER

Fluke 325 True RMS Clamp Meter

⭐ 4.8/5 · Our Rating · Built to Last
40 / 400 A
AC/DC RANGES
600 V
AC/DC VOLTS
True RMS
MEASURING
Temp
+ CAPACITANCE
Buy on Amazon β†’
Fluke 325 True RMS AC DC clamp meter

If you want one clamp that covers your projects and the rest of the house, the Fluke 325 is the safe choice. It measures AC and DC current on 40 A and 400 A ranges, AC and DC voltage to 600 V, resistance, continuity, capacitance, frequency and temperature with a thermocouple probe, all with True RMS accuracy and Fluke’s build quality and safety ratings. The jaw takes conductors up to about 30 mm. Its lowest current range is 40 A, so it’s better at checking a 12 V or 24 V supply, a motor or a solar charge line than reading the few hundred milliamps of a single ESP32 board.

βœ… Pros
  • Trusted Fluke accuracy
  • AC and DC current
  • Temperature and capacitance
  • Real safety rating
❌ Cons
  • No milliamp current range
  • Costs several times the UNI-T
🎯 Verdict: The buy-once clamp meter for power wiring, mains and bigger DC systems. Pair it with the UT210E for small currents.

πŸ‘‰ Check Price on Amazon β†’

πŸ”§ Detailed Reviews: More Clamp Meters

πŸ“± BEST BLUETOOTH LOGGING Β· ⭐ 4.4/5

3. OWON CM2100B Smart Clamp Meter

2 A / 20 A / 100 A AC and DC Β· 20000 counts Β· 17 mm jaw Β· Bluetooth app with recording Β· True RMS
Buy Here β†’
OWON CM2100B Bluetooth AC DC clamp meter

The CM2100B takes the UT210E’s winning formula, a small 17 mm jaw and a 2 A AC/DC range with milliamp steps, and adds a 20000 count display and Bluetooth. The phone app shows live readings and records them over time, so you can log how much current a project draws through a full cycle: an irrigation pump running, a battery charging or a heater thermostat switching. On Amazon, choose the CM2100B (Bluetooth) option; the plain CM2100 is the same meter without the app.

βœ… Pros: Milliamp range; higher resolution display; app logging.
❌ Cons: Lesser-known brand; listing has two variants.
🎯 Verdict: The pick if you want to record current over time from your phone.
πŸ”¦ BEST FEATURE VALUE Β· ⭐ 4.7/5

4. Klein Tools CL810 Clamp Meter with Worklight

10 mA to 600 A AC/DC Β· 6000 counts Β· 36 mm jaw Β· DC microamps via leads Β· inrush, LoZ, NCVT Β· CAT IV 600 V
Buy Here β†’
Klein Tools CL810 AC DC clamp meter with worklight

The CL810 replaces Klein’s popular CL800 and packs in more functions than any other meter here. The jaw reads AC and DC current from 10 mA to 600 A with auto-ranging, and the test leads add a DC microamp function for HVAC flame sensors that also helps with low-current electronics checks. There’s inrush current for motors and compressors, LoZ mode to ignore ghost voltages, a non-contact voltage tester, temperature, capacitance and frequency, a 6000 count display and a built-in worklight for dark cabinets. It carries CAT IV 600 V and CAT III 1000 V ratings.

βœ… Pros: Huge feature list; worklight; strong safety rating.
❌ Cons: Big jaw is clumsy on small wiring; bulky.
🎯 Verdict: The most capable clamp for the money if you also do home electrical and HVAC work.
🧲 BEST FOR TIGHT ENCLOSURES · ⭐ 4.6/5

5. Fluke 365 Detachable Jaw Clamp Meter

200 A AC/DC Β· 0.1 A resolution Β· 18 mm jaw on a flexible cable Β· True RMS Β· 600 V AC/DC
Buy Here β†’
Fluke 365 detachable jaw AC DC clamp meter

The Fluke 365 solves a real problem in project enclosures and control panels: you can’t always fit a whole meter in to clamp a wire and still see the screen. Its slim 18 mm jaw detaches and connects to the body with a flexible cable, so you can clamp a wire deep inside a box while the display sits outside. It reads AC and DC current to 200 A with 0.1 A resolution, plus 600 V AC/DC, resistance and continuity, with Fluke’s usual build quality.

βœ… Pros: Detachable slim jaw; Fluke quality; DC current.
❌ Cons: 0.1 A steps only; fewer extras than the Klein.
🎯 Verdict: The best clamp for crowded enclosures, DIN rail panels and hard-to-reach wiring.
πŸ’Ž BEST FOR SOLAR AND BATTERY BANKS Β· ⭐ 4.8/5

6. Fluke 376 FC True RMS Clamp Meter with iFlex

999.9 A AC/DC jaw Β· 34 mm jaw Β· iFlex probe to 2500 A AC Β· 1000 V Β· Fluke Connect app
Buy Here β†’
Fluke 376 FC clamp meter with iFlex probe kit

The 376 FC is Fluke’s top general-purpose clamp, and the one to choose if your ESP32 work extends to off-grid solar, battery banks, EV charging or inverter projects. The 34 mm jaw reads AC and DC current to 999.9 A with 0.1 A resolution, the included iFlex flexible probe wraps around thick cables or bus bars for AC current up to 2500 A, and voltage goes to 1000 V AC/DC. Fluke Connect sends readings to your phone for logging and sharing. It’s far more meter than a breadboard needs, but nothing else here is as capable on big DC systems.

βœ… Pros: Huge DC range; iFlex probe; app logging; top safety ratings.
❌ Cons: Expensive; no milliamp range; iFlex is AC only.
🎯 Verdict: The premium choice for solar, battery and high-current DC builds.
πŸ“ˆ BEST FOR OSCILLOSCOPES Β· ⭐ 4.3/5

7. Hantek CC-650 AC/DC Current Clamp

20 mA to 650 A DC Β· 400 Hz bandwidth Β· two sensitivity ranges Β· BNC output for scopes and DMMs
Buy Here β†’
Hantek CC-650 AC DC current clamp for oscilloscopes

The CC-650 isn’t a meter: it’s a current clamp with no display that turns current into a voltage on a BNC connector. Plug it into an oscilloscope and you can see current as a waveform: a motor’s start-up surge, the current ripple of a buck converter feeding your ESP32 project, or how a solenoid draws current when a relay fires. It reads DC from about 20 mA to 650 A, has two sensitivity settings and a 400 Hz bandwidth, which suits motors, power supplies and slow events rather than fast switching edges. It can also feed a multimeter’s millivolt range.

βœ… Pros: Turns any scope into a current analyzer; wide DC range.
❌ Cons: Needs a scope or DMM; limited bandwidth; zero drifts.
🎯 Verdict: The add-on to buy if you already own an oscilloscope and want to see current, not just measure it.

🧭 Which Clamp for Which ESP32 Job?

JobTypical CurrentUse
ESP32 Wi-Fi and Bluetooth activityTens to hundreds of mAUNI-T UT210E or OWON CM2100B
ESP32 deep sleepMicroampsNot a clamp job: use a USB power meter or current profiler
WLED and addressable LED strips1 to 20 AUNI-T UT210E, Klein CL810 or Fluke 325
Pumps, motors and solenoids0.5 to 10 A plus surgesKlein CL810 (inrush) or Hantek CC-650 on a scope
Wiring inside enclosures and DIN panelsAnyFluke 365
Logging a project over hoursmA to 100 AOWON CM2100B or Fluke 376 FC
Solar charge lines and battery banks10 to 500 A DCFluke 376 FC or Fluke 325

πŸ›’ Which One Should You Buy?

🧰

Mostly ESP32 and LED projects

The UNI-T UT210E. Its milliamp range is what small projects need.

πŸ“±

Want to log readings

The OWON CM2100B for small currents, the Fluke 376 FC for big ones.

🏠

Projects plus home wiring

The Fluke 325 or the feature-packed Klein CL810.

πŸ“ˆ

You own an oscilloscope

Add the Hantek CC-650 to see current waveforms.

❓ Frequently Asked Questions

Can a clamp meter measure ESP32 deep sleep current?

No. Deep sleep is in the microamp range, far below what any clamp can resolve. Measure it in series with a USB power meter, a current profiler or a multimeter’s microamp range.

Why does my clamp read zero on a DC wire?

Either the meter only measures AC current, or you clamped both wires of the pair. The supply and return currents cancel out, so clamp only the positive or the negative wire.

How do I get accurate readings at low current?

Press the zero button with the jaw closed and away from the wire, then clamp. Keep the wire centred in the jaw, away from magnets and transformers. For tiny currents, loop the wire through the jaw several times and divide the reading by the number of turns.

Do I still need a multimeter?

Yes. Most clamps here measure voltage and resistance too, but a dedicated multimeter has better low-current, voltage and continuity performance with fine probes for small boards. The clamp complements it.

Is it safe to clamp mains wiring in my projects?

Clamping an insulated wire is the safest way to measure mains current, as you never touch the conductor. Use a meter with a real CAT rating, such as the Fluke or Klein models, and keep enclosures closed and fused.

🏁 Final Verdict: Best Clamp Meters for Electronics

The right clamp for each job:

πŸ₯‡ Best for ESP32 Projects: UNI-T UT210E
Buy Here β†’
πŸ† Best All-Round Pro Meter: Fluke 325
Buy Here β†’
πŸ“± Best Bluetooth Logging: OWON CM2100B
Buy Here β†’
πŸ”¦ Best Feature Value: Klein CL810
Buy Here β†’
🧲 Best for Tight Enclosures: Fluke 365
Buy Here β†’
πŸ’Ž Best for Solar and Battery Banks: Fluke 376 FC
Buy Here β†’
πŸ“ˆ Best for Oscilloscopes: Hantek CC-650
Buy Here β†’

For most ESP32 makers, the UNI-T UT210E is the clamp to start with: it’s the only affordable way to read milliamps of DC without breaking a circuit. Step up to the Fluke 325 or Klein CL810 if your projects reach into home wiring, and to the Fluke 376 FC for solar and battery systems. To round out your current measurement kit, see our guides to multimeters, USB power meters and current profilers for deep sleep testing, oscilloscopes to pair with the Hantek clamp, and ESP32 energy monitors for permanent current logging.

πŸ’¬ Not sure which clamp suits your project? Tell us what you’re measuring in the comments below, and we’ll help you choose.

All Amazon links above use our affiliate tag (esp32tutorials-20). Purchasing through them supports esp32tutorials.com at no extra cost to you. Prices and availability change frequently, so always confirm the current price on Amazon before buying.

Leave a Comment