β οΈ Affiliate Disclosure: This post contains Amazon affiliate links. If you purchase through our links, we may earn a small commission at no extra cost to you. Every product below was checked against its live Amazon listing before publishing. Prices change often, so we don’t list them here. Tap any Buy Here button to see the current price on Amazon.
Ultimate Buying Guide
π‘ Best mmWave Presence Sensors for ESPHome and Home Assistant
PIR sensors turn the lights off while you sit still. mmWave radar sees a person breathing. Here are 8 picks, from bare radar modules for your own ESP32 build to ready-made ESPHome sensors and zone-tracking units.
β
8 Sensors Compared
β
Verified Amazon ASINs
β
Range and Zones Explained
β
Honest Pros & Cons
Presence detection is where many ESP32 home automation projects start: lights that stay on while you read, a desk fan that turns off when you leave, heating that follows the room you’re actually in. A PIR sensor only reacts to movement, so it gives up on anyone sitting still. A 24 GHz or 60 GHz mmWave radar detects the tiny movements of breathing, so it can report “someone is here” for as long as they are.
The ESP32 is the natural partner for these radars. Most modules talk UART, ESPHome has ready-made components for the popular chips, and several finished sensors are simply an ESP32 and a radar in a nice case. This guide compares 8 picks across three groups: bare modules for your own build, ESP32-based ESPHome sensors, and a polished zone-tracking sensor for comparison.
π‘ Before you buy: mmWave radar sees through thin plastic, drywall and glass, and it also sees fans, curtains moving in a draft and pets. Plan to spend a little time tuning sensitivity and distance gates, mount the sensor facing into the room rather than at a doorway or window, and keep it away from vibrating surfaces. Every sensor here needs constant power; none run for long on a battery.
β‘ Quick Comparison: All 8 Sensors
| Sensor | Type | Key Spec | Best For | Buy |
|---|
| π₯ Seeed XIAO MR60BHA2 | ESP32-C6 kit | 60 GHz, presence to 6 m, ESPHome pre-flashed | Best Ready-to-Use ESP32 Kit | Buy Here β |
| π§© DFRobot Fermion C4002 | Radar module | 24 GHz, static to 10 m, 120Β° Γ 120Β° | Best Module for DIY ESPHome | Buy Here β |
| πΊοΈ Aqara Presence Sensor FP2 | Finished sensor | Up to 30 zones, 5 people, 40 mΒ² | Best Zone Tracking, No Soldering | Buy Here β |
| π DFRobot Gravity C4001 | Radar module | 24 GHz, presence 8 m, motion 12 m, I2C/UART | Best Long Range | Buy Here β |
| π° Hi-Link HLK-LD2410C | Radar module | 24 GHz, 5 m, UART + GPIO, Bluetooth setup | Best Budget Module | Buy Here β |
| π― Everything Presence Lite | ESP32 sensor | LD2450, tracks 3 targets, BLE proxy | Best Multi-Target ESPHome Sensor | Buy Here β |
| π‘οΈ Apollo Automation MSR-2 | ESP32 multisensor | mmWave + lux, pressure, UV, RGB, buzzer | Best Multisensor | Buy Here β |
| π Seeed XIAO MR60FDA2 | ESP32-C6 kit | 60 GHz fall detection, 3 Γ 3 Γ 3 m | Best for Fall Detection | Buy Here β |
Specs come from the manufacturers and the live Amazon listings. Star scores below are our ratings.
π What Matters in an mmWave Sensor
π§
Static Presence Range
Motion range is always bigger. The number that matters is how far it can still see someone sitting or lying still.
πΊοΈ
Zones and Targets
Basic radars only say “someone is here”. Tracking radars report positions, so you can define a desk zone or a sofa zone.
π
Interface
UART gives distance and tuning data; a GPIO output is a simple occupied pin. I2C is handy when your UARTs are busy.
π
ESPHome Support
A ready ESPHome component or YAML saves hours of protocol work and gives you tuning entities in Home Assistant.
π‘
Extra Sensors
A light sensor lets automations skip turning lights on in daylight, which is the most common presence use.
π Detailed Reviews: The Top Two
π₯ BEST READY-TO-USE ESP32 KIT
Seeed Studio XIAO MR60BHA2 60GHz mmWave Kit
β 4.7/5 Β· Our Rating Β· ESPHome Out of the Box
Buy on Amazon β

This kit is the quickest route from box to working presence sensor that still runs on hardware you can reprogram. Seeed pairs a 60 GHz mmWave radar with a XIAO ESP32-C6, a BH1750 light sensor (1 to 65,535 lux) and a WS2812 RGB LED, all pre-flashed with ESPHome. Power it from a 5 V USB supply, join it to Wi-Fi and Home Assistant discovers it. It detects human presence up to 6 m and, within about 1.5 m, breathing and heart rate, which makes it interesting for bedside and desk automations. Grove ports leave room to add sensors, and because it’s ESPHome you can edit the YAML like any other ESP32 project.
β
Pros- ESPHome pre-flashed
- Light sensor and RGB LED
- Wi-Fi and Bluetooth
- Breathing and heart rate
β Cons- Vital signs only up close
- No zone tracking
- Bare-board style case
π― Verdict: The easiest ESP32-based presence sensor to set up, with headroom for your own ESPHome tweaks.
π Check Price on Amazon β
π§© BEST MODULE FOR DIY ESPHOME BUILDS
DFRobot Fermion C4002 mmWave Presence Sensor
β 4.6/5 Β· Our Rating Β· Wide-Angle Module
Buy on Amazon β

If you want to build your own sensor around an ESP32, the C4002 is the module to start with. This 24 GHz FMCW radar detects motion up to 11 m and static or micro-motion presence up to 10 m across a wide 120Β° Γ 120Β° field, so one unit covers most living rooms from a corner. It learns the background noise of the room, the detection distance is set in software, and DFRobot states it’s fully compatible with ESPHome, with a verified YAML config that exposes occupancy, distance and energy entities in Home Assistant. Wire it to any spare UART on your ESP32, or use the simple OUT pin. It runs from 3.6 to 5.5 V on a 22 Γ 26 mm board.
β
Pros- Long static range
- Very wide field of view
- ESPHome YAML provided
- Tiny and affordable
β Cons- Needs your own ESP32 and case
- No multi-target tracking
π― Verdict: The best radar module for a DIY ESP32 room-presence sensor.
π Check Price on Amazon β
π§ Detailed Reviews: More Sensors and Modules
πΊοΈ BEST ZONE TRACKING, NO SOLDERING Β· β 4.5/53. Aqara Presence Sensor FP2
Up to 30 zones Β· up to 5 people Β· 40 mΒ² room Β· light sensor Β· IPX5 Β· USB-C powered
Buy Here β

The FP2 isn’t an ESP32 device, but it’s the benchmark every DIY presence sensor gets compared with, so it belongs here. One wall, ceiling or corner-mounted unit covers a room of up to 40 mΒ², tracks up to 5 people and lets you draw up to 30 zones in the Aqara app, such as a desk, a sofa and a bed. It includes a light sensor, offers fall detection when ceiling-mounted, and works over Wi-Fi with no hub. Home Assistant picks it up through the HomeKit Controller integration. Choose it when you want zones without designing anything; choose an ESP32 build when you want full local control and custom firmware.
β
Pros: Excellent zone tracking; polished app; no build needed.
β Cons: Closed firmware; zones set in Aqara app; not ESPHome.
π― Verdict: The best finished zone sensor if you don’t need to flash it yourself.
π BEST LONG RANGE Β· β 4.5/54. DFRobot Gravity C4001 mmWave Sensor (12 m)
24 GHz FMCW Β· presence 8 m Β· motion 12 m Β· speed sensing Β· I2C and UART Β· 3.3 or 5 V
Buy Here β

The C4001 reaches further than most modules: 8 m for presence and 12 m for motion and ranging, with speed measurement from 0.1 to 10 m/s. That suits garages, hallways and large open-plan rooms. Its standout feature for ESP32 builds is I2C as well as UART, on a Gravity PH2.0 connector, so you can hang it on an existing I2C bus alongside other sensors and keep your UARTs free. It runs on 3.3 or 5 V and DFRobot provides Arduino libraries that work on ESP32. The beam is 100Β° Γ 80Β°, narrower than the C4002.
β
Pros: Long range; I2C option; speed and distance data; 3.3 V friendly.
β Cons: Narrower beam; ESPHome setup takes more work.
π― Verdict: The pick for long rooms, garages and corridors.
π° BEST BUDGET MODULE Β· β 4.4/55. Hi-Link HLK-LD2410C Human Presence Radar Module
24 GHz FMCW Β· up to 5 m Β· Β±60Β° coverage Β· UART + GPIO output Β· Bluetooth configuration
Buy Here β

The LD2410 family is the radar inside many commercial and DIY presence sensors, and the LD2410C version adds standard 2.54 mm header pins so it plugs straight into Dupont jumpers. It detects presence up to about 5 m over Β±60Β°, outputs a simple occupied signal on a GPIO pin plus detailed data over UART, and can be tuned from a phone app over Bluetooth. ESPHome has a built-in LD2410 component that exposes every distance gate as a sensitivity slider in Home Assistant, which makes tuning easy. It’s the cheapest way to add mmWave to an ESP32 project. Supply it with 5 V rather than 3.3 V.
β
Pros: Very cheap; native ESPHome component; header pins; per-gate tuning.
β Cons: Shorter range; sold by many resellers, so quality can vary.
π― Verdict: The best value radar for your first ESP32 presence build.
β Also Worth Considering
π― BEST MULTI-TARGET ESPHOME SENSOR Β· β 4.6/5
6. Everything Presence Lite
An ESP32 and ESPHome sensor built around the LD2450 tracking radar. It follows up to 3 targets with distance, angle, speed and X/Y position across roughly 5 to 6 m, so you can set zones directly in Home Assistant. It adds an ambient light sensor, works as a Bluetooth proxy and ships in a 3D-printed case with a right-angle USB-C cable.
Buy Here βπ‘οΈ BEST MULTISENSOR Β· β 4.5/5
7. Apollo Automation MSR-2
An open-source ESP32 multisensor for Home Assistant that combines an LD2410B mmWave radar with lux, air pressure, temperature and UV sensing, an RGB LED and a piezo buzzer. An expansion slot takes an optional CO2 sensor. It’s the pick when one small box should handle presence and room conditions together.
Buy Here βπ BEST FOR FALL DETECTION Β· β 4.4/5
8. Seeed Studio XIAO MR60FDA2 Kit
The sister kit to our top pick, tuned for fall detection over a 3 Γ 3 Γ 3 m area, with static presence up to 6 m. It uses the same XIAO ESP32-C6, BH1750 light sensor and RGB LED, ships with ESPHome pre-flashed and runs from 5 V USB. The radar firmware itself is closed, so treat it as a helpful alert, not a medical device.
Buy Here βπ Which Sensor for Which ESP32 Job?
| Project | What You Need | Best Pick |
|---|
| Lights that stay on while you read | Static presence + lux | Seeed XIAO MR60BHA2 |
| Custom ESPHome room sensor | Module + your ESP32 | DFRobot C4002 or HLK-LD2410C |
| Desk, sofa and bed zones | Multi-target tracking | Everything Presence Lite or Aqara FP2 |
| Garage or long hallway | 8 to 12 m range | DFRobot Gravity C4001 |
| Presence plus climate in one box | Multisensor | Apollo MSR-2 |
| Alert for a relative living alone | Fall detection | Seeed XIAO MR60FDA2 |
π Which One Should You Buy?
β‘
Working tonight
The Seeed XIAO MR60BHA2 kit: plug in, join Wi-Fi, done.
π οΈ
You enjoy building
A DFRobot C4002 or a pack of LD2410C modules and spare ESP32 boards.
πΊοΈ
You want zones
Everything Presence Lite for ESPHome, Aqara FP2 for no setup.
β Frequently Asked Questions
What’s the difference between mmWave and PIR?
PIR sensors detect changes in heat as someone moves across the field of view, so they miss people sitting still. mmWave radar measures tiny movements such as breathing, so it keeps reporting presence. Many projects combine both: PIR for an instant trigger, mmWave to hold the state.
How do I connect an mmWave module to an ESP32?
Most modules use UART: module TX to an ESP32 RX pin, module RX to a TX pin, plus power and ground. Use a spare hardware UART rather than the one used for USB logging, and check the module’s supply voltage, since many need 5 V even though their data lines are 3.3 V.
Why does my sensor report presence in an empty room?
Ceiling fans, moving curtains, pets, vibrating appliances and even the radar seeing through a wall into the next room are the usual causes. Reduce the maximum distance, lower sensitivity on the far gates and re-aim the sensor away from the source.
Can mmWave sensors run on batteries?
Not practically. The radar and the ESP32’s Wi-Fi draw power continuously, so these sensors need a USB supply. If a room has no outlet, a battery PIR sensor with an ESP32 in deep sleep is the better choice.
Is 24 GHz or 60 GHz better?
24 GHz modules are cheaper and reach further, which suits general room presence. 60 GHz radars have finer resolution, which is why they’re used for breathing, heart rate and fall detection at shorter range.
π Final Verdict: Best mmWave Presence Sensors
The right radar for each room:
π₯ Best Ready-to-Use ESP32 Kit: Seeed XIAO MR60BHA2
Buy Here βπΊοΈ Best Zone Tracking: Aqara Presence Sensor FP2
Buy Here βFor most ESP32 and Home Assistant setups, the Seeed XIAO MR60BHA2 is the fastest way to reliable presence, while the DFRobot C4002 and HLK-LD2410C are the modules to build your own around. Add the Everything Presence Lite or Aqara FP2 when you need zones. To round out your smart home, see our ESP32 sensors, Home Assistant servers and Bluetooth proxy sensors guides, plus our ESP32-C6 boards roundup for your own builds.
π¬ Which room are you trying to automate? Tell us in the comments below, and we’ll suggest the right sensor and mounting spot.
All Amazon links above use our affiliate tag (esp32tutorials-20). Purchasing through them supports esp32tutorials.com at no extra cost to you. Prices and availability change frequently, so always confirm the current price on Amazon before buying.
We are a team of experienced Embedded Software Developers with skills in developing Embedded Linux, RTOS, and IoT products from scratch to deployment with a demonstrated history of working in the embedded software industry. Contact us for your projects: admin@esp32tutorials.com