Best PoE Switches, Injectors and Splitters for ESP32: 9 TP-Link, TRENDnet, Zyxel, YuanLey, UCTRONICS and REVOTECH Picks Compared (Buying Guide)

⚠️ Affiliate Disclosure: This post contains Amazon affiliate links. If you purchase through our links, we may earn a small commission at no extra cost to you. Every product below was checked against its live Amazon listing before publishing. Prices change often, so we don’t list them here. Tap any Buy Here button to see the current price on Amazon.
Ultimate Buying Guide

πŸ–§ Best PoE Switches, Injectors and Splitters for ESP32

One Ethernet cable for power and data. Here are 9 switches, injectors and splitters that run ESP32 PoE boards, Zigbee coordinators and remote sensor nodes without a single wall adapter.

βœ… 9 Picks Compared βœ… Verified Amazon ASINs βœ… 802.3af vs PoE+ Explained βœ… Honest Pros & Cons

Wi-Fi is easy until an ESP32 has to live in a ceiling void, a garage, a metal cabinet or a garden shed. Ethernet boards such as the WT32-ETH01, Olimex ESP32-POE, LILYGO T-ETH and Waveshare ESP32-S3-ETH solve the radio problem, and Power over Ethernet solves the power problem: one Cat5e or Cat6 cable carries both, up to 100 m, with no USB charger or 5 V supply at the far end.

To make that work you need a PoE source (a PoE switch or an injector) and, for boards without PoE built in, a splitter that turns the 48 V feed back into 5 V or 12 V. This guide compares 9 picks from TP-Link, TRENDnet, Zyxel, YuanLey, UCTRONICS and REVOTECH, from single-port injectors to managed switches that keep IoT gear on its own VLAN.

πŸ’‘ Before you buy: Check that your board expects standard IEEE 802.3af/at PoE, not passive 24 V PoE. Every pick here is standards based, so it only sends power after it detects a valid PoE device, and laptops or routers on the same switch just get data. An ESP32 PoE board draws only a few watts, so any 802.3af port is enough; you only need PoE+ (30 W) ports when the same switch also feeds cameras, access points or a Raspberry Pi 5 PoE+ HAT. Many cheap “PoE” ESP32 boards ship the PoE module as an option, so confirm it is fitted before you plug in.

⚑ Quick Comparison: All 9 Picks

ProductTypeKey SpecBest ForBuy
πŸ₯‡ TP-Link TL-SG105MPE5-port Easy Smart switch4 x PoE+ (30 W), 120 W budget, VLANsBest OverallBuy Here β†’
⚑ TRENDnet TPE-115GISingle-port injector30 W 802.3at, gigabit, 100 mBest InjectorBuy Here β†’
πŸ”§ TP-Link TL-SG108PE8-port Easy Smart switch4 x 802.3af PoE, VLAN, QoSBest 8-Port for ESP32 NodesBuy Here β†’
πŸ’° YuanLey 5-Port PoEUnmanaged switch4 x PoE+, 78 W built-in supplyBest Budget SwitchBuy Here β†’
🟦 Zyxel GS1005HPUnmanaged switch4 x PoE+, 60 W, budget LEDBest Quiet Desk SwitchBuy Here β†’
πŸ”· TP-Link Omada POE160SSingle-port injectorUp to 30 W, gigabit, ULBest Compact InjectorBuy Here β†’
πŸ”Œ UCTRONICS USB-C SplitterActive splitter802.3af in, 5 V USB-C + RJ45 outBest for Wi-Fi ESP32 BoardsBuy Here β†’
πŸ”‹ REVOTECH 12V SplitterActive splitter802.3af/at in, 12 V 2 A on 5.5×2.1 mmBest for 12 V Relay BoardsBuy Here β†’
πŸ” TP-Link TL-SG1005P-PDPoE-powered switch1 PoE in, 4 x PoE+ outBest for Remote ClustersBuy Here β†’

Specs come from each manufacturer page or Amazon listing at the time of writing and can change. Always confirm details on the product page.

πŸ” What Matters for ESP32 PoE Projects

πŸ“œ

PoE Standard

802.3af gives up to 15.4 W per port, 802.3at (PoE+) up to 30 W. ESP32 PoE boards and splitters work on either, because PoE+ ports are backward compatible.

πŸ”‹

Total PoE Budget

The budget is shared across all PoE ports. ESP32 nodes barely dent it, but cameras and access points can use most of it, so add up every device and keep headroom.

πŸ”

VLAN Support

Easy Smart switches can put ESP32 nodes and cheap IoT gadgets on their own VLAN, away from your PCs. Unmanaged switches are simpler but cannot segment traffic.

πŸ”€

Switch, Injector or Splitter

A switch powers several drops, an injector adds PoE to one cable from a normal router, and a splitter powers a board that has no PoE circuit of its own.

πŸ”Œ

Output Voltage

Splitters output a fixed voltage. Pick 5 V USB-C for dev boards and 12 V barrel for relay boards, LED controllers and anything with an onboard regulator.

πŸ† Detailed Reviews: The Top Two

πŸ₯‡ BEST OVERALL POE SWITCH FOR ESP32 PROJECTS

TP-Link TL-SG105MPE 5-Port Easy Smart PoE+ Switch

⭐ 4.7/5 · Our Rating · Small, Managed, Powerful
120 W
POE BUDGET
4 x PoE+
30 W PER PORT
5
GIGABIT PORTS
VLAN
QOS, IGMP
Buy on Amazon β†’
TP-Link TL-SG105MPE 5-port Easy Smart PoE+ switch

The TL-SG105MPE is the switch we would put on an ESP32 bench or in a smart home network cupboard. Four of its five gigabit ports are 802.3at/af PoE+ with up to 30 W each from a 120 W total budget, so it can run an ESP32 PoE board, an SLZB-style Zigbee coordinator, a camera and an access point at the same time with room to spare. Unlike plug-and-play switches it is Easy Smart managed: you can put ESPHome nodes and cheap IoT gadgets on their own VLAN, set QoS and enable IGMP snooping. The fifth port uplinks to your router.

βœ… Pros
  • Full 30 W on all four PoE ports
  • VLANs to isolate IoT devices
  • Compact desktop size
❌ Cons
  • Only five ports in total
  • Web UI is basic next to Omada or UniFi
🎯 Verdict: The best small PoE switch for most ESP32 and Home Assistant setups.
πŸ‘‰ Check Price on Amazon β†’
⚑ BEST INJECTOR FOR ONE ESP32 DROP

TRENDnet TPE-115GI Gigabit PoE+ Injector

⭐ 4.7/5 · Our Rating · Add PoE to Any Router
30 W
POE+ OUTPUT
af / at
STANDARDS
100 m
CABLE RUN
Gigabit
DATA
Buy on Amazon β†’
TRENDnet TPE-115GI gigabit PoE+ injector

If you only have one ESP32 to power, you don’t need a new switch. The TPE-115GI sits between any normal gigabit port and your device and adds up to 30 W of 802.3at PoE+, while still feeding 802.3af devices such as ESP32 PoE boards and splitters. TRENDnet rates it for runs up to 100 m (328 ft), it is wall mountable and it passes full gigabit data. It is the simplest way to put a WT32-ETH01 with a PoE module, an Olimex ESP32-POE or a PoE Zigbee coordinator at the far end of a long cable.

βœ… Pros
  • Works with any router or switch
  • Plenty of power headroom
  • Long-proven, widely reviewed
❌ Cons
  • Powers one device only
  • Needs an AC outlet at the router end
🎯 Verdict: The reliable way to add PoE to a single ESP32 drop.
πŸ‘‰ Check Price on Amazon β†’

πŸ”§ Detailed Reviews: Switches, Injectors and Splitters

πŸ”§ BEST 8-PORT FOR ESP32 NODES Β· ⭐ 4.6/5

3. TP-Link TL-SG108PE V3 8-Port Easy Smart PoE Switch

8 gigabit ports Β· 4 x 802.3af PoE Β· VLAN, QoS, IGMP snooping
Buy Here β†’
TP-Link TL-SG108PE 8-port Easy Smart PoE switch

This is the switch for a workbench or cupboard full of low-power ESP32 gear. You get eight gigabit ports, four of them with 802.3af PoE (15.4 W each), and the same Easy Smart management as our top pick for VLANs, QoS and IGMP snooping. Since ESP32 PoE boards and USB-C splitters draw only a few watts, standard PoE is all they need, and the four non-PoE ports cover your PC, Home Assistant box and router uplink. It is PoE, not PoE+, so it will not run 30 W devices such as a Raspberry Pi 5 PoE+ HAT.

βœ… Pros: 8 ports; VLANs; ideal for many small PoE loads.
❌ Cons: 802.3af only; smaller budget than PoE+ models.
🎯 Verdict: The best value managed switch when your PoE devices are ESP32 boards and sensors.
πŸ’° BEST BUDGET SWITCH Β· ⭐ 4.4/5

4. YuanLey 5-Port Gigabit PoE Switch (4 PoE+, 78 W)

4 x 802.3af/at Β· 78 W built-in supply Β· fanless metal Β· unmanaged
Buy Here β†’
YuanLey 5-port gigabit PoE switch with 78W budget

YuanLey’s popular unmanaged switch is the cheapest way to get proper PoE+ ports on the bench. It provides four 802.3af/at ports fed from a 78 W built-in power supply, so there is no external brick, plus a gigabit uplink, all in a fanless metal case. Plug it in and every ESP32 PoE board, splitter or small camera on it powers up with no setup. With 78 W in total, it handles a mix of ESP32 nodes and two or three heavier devices.

βœ… Pros: Built-in PSU; silent; PoE+ on all four ports.
❌ Cons: No VLANs; lesser-known brand.
🎯 Verdict: The budget pick for a plug-and-play ESP32 PoE bench.
🟦 BEST QUIET DESK SWITCH · ⭐ 4.5/5

5. Zyxel GS1005HP 5-Port Gigabit PoE+ Switch

4 x 802.3at Β· 60 W shared budget Β· MAX budget LED Β· fanless
Buy Here β†’
Zyxel GS1005HP 5-port gigabit PoE+ switch

Zyxel’s compact switch is a tidy choice for a desk or a shelf next to your router. It offers four 802.3at PoE+ ports (up to 30 W each) inside a 60 W shared budget, and a handy MAX LED turns orange when the total draw reaches 50 W, so you know before you overload it. It is fanless and silent. For ESP32 work the 60 W budget is generous; it only gets tight if you also run several PoE+ cameras or access points.

βœ… Pros: Budget warning LED; quiet; known brand.
❌ Cons: 60 W total is tight for PoE+ loads; fewer reviews.
🎯 Verdict: A silent, branded switch for light PoE loads like ESP32 boards.
πŸ”· BEST COMPACT INJECTOR Β· ⭐ 4.6/5

6. TP-Link Omada POE160S PoE+ Injector

Up to 30 W Β· 802.3at/af Β· gigabit Β· UL certified Β· wall mountable
Buy Here β†’
TP-Link Omada POE160S gigabit PoE+ injector

TP-Link’s POE160S is a plug-and-play gigabit injector that delivers up to 30 W of PoE+ and also powers 15.4 W 802.3af devices, with UL certification and wall-mount holes. It is sold for Omada access points, but because it follows the IEEE standards it works just as well with an ESP32 PoE board, a PoE Zigbee coordinator or any splitter in this guide. Choose it over the TRENDnet if you prefer a smaller body or already run TP-Link gear.

βœ… Pros: Compact; gigabit; 30 W; trusted brand.
❌ Cons: One port; needs AC power nearby.
🎯 Verdict: A neat injector for one ESP32 board, camera or access point.
πŸ”Œ BEST FOR WI-FI ESP32 BOARDS Β· ⭐ 4.6/5

7. UCTRONICS PoE Splitter USB-C 5V

802.3af active splitter Β· 5 V USB-C output Β· RJ45 data pass-through
Buy Here β†’
UCTRONICS PoE splitter with USB-C 5V output

Most ESP32 dev boards have no Ethernet at all, but they can still take advantage of PoE for power. This 802.3af active splitter takes the PoE feed from a switch or injector and outputs 5 V on a USB-C plug, with the data on a separate RJ45 jack. Plug the USB-C end into an ESP32-S3, ESP32-C6 or ESP32-C3 board and you have a Wi-Fi or Bluetooth proxy node that runs from one network cable, ideal in a loft or outbuilding with no socket. If you use a W5500 or LAN8720 board, the RJ45 output carries the network too.

βœ… Pros: Powers any USB-C board; standard PoE; well reviewed.
❌ Cons: Adds a small box and short leads to the install.
🎯 Verdict: The easiest way to run an ordinary ESP32 dev board from PoE.
πŸ”‹ BEST FOR 12 V RELAY BOARDS Β· ⭐ 4.5/5

8. REVOTECH Gigabit PoE Splitter 12V 2A (PS5712TG)

802.3af/at input Β· 12 V 2 A on 5.5×2.1 mm Β· gigabit data
Buy Here β†’
REVOTECH gigabit PoE splitter with 12V barrel output

Many ESP32 projects run from 12 V rather than 5 V: multi-channel relay boards, WLED controllers driving 12 V strips, valve and pump controllers. This REVOTECH splitter turns an 802.3af/at feed into 12 V at 2 A on a 5.5×2.1 mm barrel plug, with gigabit data on the RJ45 side. The board’s own regulator then makes 3.3 V for the ESP32, and the relays or LEDs get the 12 V directly. Check that your board’s DC jack is 2.1 mm before you buy.

βœ… Pros: 12 V for relays and LEDs; gigabit; af or at input.
❌ Cons: 2 A limit; fixed 2.1 mm barrel.
🎯 Verdict: Our pick for putting 12 V ESP32 controllers on PoE.
πŸ” BEST FOR REMOTE CLUSTERS Β· ⭐ 4.3/5

9. TP-Link TL-SG1005P-PD 5-Port PoE Passthrough Switch

Powered by PoE in Β· 4 x PoE+ out Β· budget set by the input class
Buy Here β†’
TP-Link TL-SG1005P-PD PoE powered passthrough switch

This clever switch needs no outlet: feed one port from a PoE source and it passes power to four PoE+ outputs. TP-Link lists the output budget as 66 W, 47 W, 21 W or 9 W depending on whether the input is 802.3bt, at or af. With a PoE+ input from our top pick, that is enough for several ESP32 boards in a garage, greenhouse or garden shed on a single cable run. An 802.3af input leaves only 9 W, so plan for PoE+ at the source.

βœ… Pros: No outlet needed; one cable feeds four devices.
❌ Cons: Output budget limited by the input; fewer reviews.
🎯 Verdict: Extend PoE to a remote group of ESP32 nodes on one cable.

πŸ“ Which Pick for Which ESP32 Job?

JobWhat You NeedUse
Bench full of ESP32 PoE boards and a coordinatorSeveral PoE ports, VLANTP-Link TL-SG105MPE
One WT32-ETH01 or Olimex ESP32-POE far from the routerPoE on one cableTRENDnet TPE-115GI or TP-Link POE160S
Many low-power sensor nodes plus wired PCs8 ports, 802.3afTP-Link TL-SG108PE
Wi-Fi ESP32-S3 Bluetooth proxy in the loft5 V USB-C from PoEUCTRONICS USB-C splitter
12 V relay board or WLED controller12 V barrel from PoEREVOTECH 12V splitter
Garage or shed cluster with no outletPowered by PoE inTP-Link TL-SG1005P-PD
Cheapest plug-and-play PoE bench4 PoE+ ports, no setupYuanLey 5-Port or Zyxel GS1005HP

πŸ›’ Which One Should You Buy?

🏠

You run a Home Assistant network

Get the TP-Link TL-SG105MPE and put ESPHome nodes on their own VLAN.

1️⃣

You have one PoE device

Skip the switch and buy the TRENDnet TPE-115GI or TP-Link POE160S.

πŸ“Ά

Your board has no Ethernet

Add the UCTRONICS USB-C or REVOTECH 12V splitter to any PoE source.

πŸ’΅

You want the lowest cost

The YuanLey 5-Port gives four PoE+ ports with zero setup.

❓ Frequently Asked Questions

How much power does an ESP32 PoE board need?

Very little. An ESP32 with an Ethernet PHY typically uses well under 2 W, even with Wi-Fi active, so a single 802.3af port (15.4 W) has plenty of margin. Budget more only when the board also drives relays, LEDs or a display from the same supply.

Can a PoE switch damage my laptop or a non-PoE ESP32 board?

Not with standards-based 802.3af/at switches and injectors like the ones here. They check for a valid PoE signature before sending power, so non-PoE devices just get data. Passive PoE injectors, which put voltage on the cable all the time, are the ones to avoid.

Does the WT32-ETH01 support PoE?

Not on its own. The WT32-ETH01 needs 3.3 V or 5 V on its pins, so either add a PoE module or use a 5 V splitter and feed its 5 V pin. Boards such as the Olimex ESP32-POE, LILYGO T-ETH-POE and Waveshare ESP32-S3-ETH with the PoE module fitted take power straight from the cable.

Is it safe to connect USB while an ESP32 is on PoE?

Check your board’s documentation. Isolated PoE designs are generally fine, but on non-isolated boards a USB cable from your PC can create a ground loop through the PoE supply. Many makers flash over USB with the Ethernet cable unplugged, then use OTA updates once the board is installed.

How long can the cable be?

Ethernet and PoE are specified to 100 m (328 ft) per segment on Cat5e or better. Use solid copper cable rather than copper-clad aluminium, which drops more voltage and runs warmer under PoE load. For longer runs, a passthrough switch like the TL-SG1005P-PD can extend the network.

🏁 Final Verdict: Best PoE Gear for ESP32

The right PoE source or splitter for each job:

πŸ₯‡ Best Overall: TP-Link TL-SG105MPE
Buy Here β†’
⚑ Best Injector: TRENDnet TPE-115GI
Buy Here β†’
πŸ”§ Best 8-Port: TP-Link TL-SG108PE
Buy Here β†’
πŸ’° Best Budget: YuanLey 5-Port PoE Switch
Buy Here β†’
πŸ”Œ Best Splitter for Dev Boards: UCTRONICS USB-C 5V
Buy Here β†’
πŸ”‹ Best 12 V Splitter: REVOTECH PS5712TG
Buy Here β†’
πŸ” Best for Remote Clusters: TP-Link TL-SG1005P-PD
Buy Here β†’

For most ESP32 makers, the TP-Link TL-SG105MPE is the one switch to buy: enough PoE+ for every board, coordinator and camera on a small network, plus VLANs to keep IoT devices separate. If you only need one powered drop, a TRENDnet TPE-115GI injector does the job for far less, and the UCTRONICS and REVOTECH splitters bring PoE to boards that were never designed for it. To pick the board itself, see our ESP32 Ethernet and PoE boards guide, and for wired smart home builds check our ESP32 Zigbee and Thread coordinators, ESP32 relay boards and Home Assistant servers guides.

πŸ’¬ Running ESP32 boards on PoE already? Tell us which board and switch you use in the comments below, and share any tips for wiring PoE in tricky spots.

All Amazon links above use our affiliate tag (esp32tutorials-20). Purchasing through them supports esp32tutorials.com at no extra cost to you. Prices and availability change frequently, so always confirm the current price on Amazon before buying.

Leave a Comment