In this tutorial, we will build an ESP32 web server using ESP-IDF that will display BME680 sensor readings. BME680 environmental sensor is widely used in electronic projects to measure ambient temperature, barometric pressure, relative humidity, and gas (VOC) or Indoor air quality (IAQ). The web server will act as a weather station by displaying temperature, humidity, gas and pressure readings on the web page which will update after every 10 seconds. We will use VS Code with ESP-IDF extension to create and build this EP32 web server. It will be easily accessed on different devices such as laptops, mobiles, etc which are connected to the same Wi-Fi network as the ESP32 board.
We will program our ESP32 development board in VS Code with ESP-IDF extension. Before we move ahead, make sure you have the latest version of VS Code installed on your system with the ESP-IDF extension configured.
- Install ESP32 ESP-IDF on Windows
- Install ESP32 ESP-IDF on Linux Ubuntu
- Getting Started with ESP32 using ESP-IDF
ESP32 ESP-IDF BME680 Web Server Overview
Our ESP32 will host a web server that serves the HTML/CSS files to a web client which is a web browser. We will create the web server with the help of the HTTP web server library available in esp-idf. When a user enters the IP address in a web browser, an HTTP get request is sent to ESP32. The ESP32 responds to the request by sending a buffer which contains the HTML and CSS files to build the webpage that displays the BME680 sensor data.
Users can access the web server through an IP address and any web client application such as a web browser on your laptop or mobile phone.
BME680 Introduction
BME680 is a four in one low power-driven sensor, which has integrated temperature, pressure, humidity, and gas sensors. It runs on an operating voltage of 1.8-3.8V and communicates with other microcontrollers through I2C and SPI protocol. This sensor is used in areas such as tracking the quality of air, humidity indicators, weather trends, home automation, and controlling GPS enhancements.
Pinout Diagram
The pinout diagram of BME680 sensor is shown below:
| Pin Name | Description |
|---|---|
| VCC | Pin to power up sensor |
| GND | GND pin for power supply |
| SCL | BME680 provides 2 interfaces such as SPI and I2C to get sensor readings. This pin is serial clock signal for both I2C and SPI interfaces. |
| SDA | With I2C protocol this pin acts as SDA or Serial Data pin and when using SPI protocol this pin acts as SDI or Serial Data In also known as MOSI (‘Master out Slave in’). |
| SDO | This is the SDO (Slave data out) /MISO (Master in slave out) pin for SPI communication. This pin is used for SPI interface only. |
| CS | This is the Chip Select pin used in SPI communication. Acts as an input to the sensor. |
ESP32 I2C Pins
We will be using I2C interface to get BME680 sensor readings with ESP32 and ESP-IDF. Now let’s discuss I2C pins of ESP32. The diagram below shows the pinout for the ESP32, where the default I2C pins are highlighted in red. These are the default I2C pins of the ESP32 DEVKIT module. However, if you want to use other GPIO pins as I2C pins then you will have to set them in code.
Refer to the following article to know more about ESP32 GPIO pins:
You can check this complete guide on ESP32 I2C communication:
Interface BME680 with ESP32 ESP-IDF
We will need the following components to connect ESP32 board with BME680.
- ESP32 board
- BME680 Sensor
- Connecting Wires
- Breadboard
The connection of BME680 with the ESP32 board is straightforward as it just involves the connection of the 4 pins (GND, VCC, SDA, and SCL) with ESP32. We have to connect the VCC terminal with 3.3V pin, ground with the ground (common ground), SCL of the sensor with SCL of ESP32 board, and SDA of the sensor with the SDA pin of the ESP32 board.
In ESP32, the default I2C pin for SDA is GPIO21 and for SCL is GPIO22.
The connections between the devices are specified in the table below:
| BME680 Sensor | ESP32 |
|---|---|
| GND | GND |
| VCC | 3.3V |
| SDA | GPIO21(I2C SDA) |
| SCL | GPIO22 (I2C SCL) |
ESP32 BME680 Web Server with ESP-IDF
We will build and create a project in VS Code with ESP-IDF extension to measure ambient temperature, barometric pressure, relative humidity, and gas (VOC) or Indoor air quality (IAQ) from BME60 environmental sensor and display these values on web page.
The code creates a web server on ESP32 which hosts HTML/CSS files and reads sensor measurements. Moreover, whenever any http client request received from a web page, it will server web pages along with BME680 sensor values. We will use the BME680 ESP-IDF library provided by UncleRus on GitHub.
Create Example Project
Open your VS Code and head over to View > Command Palette. Type ESP-IDF: New Project in the search bar and press enter.
Specify the project name and directory, along with the ESP-IDF board and target. For the ESP-IDF board, we have chosen the custom board option. For ESP-IDF target, we have chosen ESP32 module. Click ‘Choose Template’ button to proceed forward.
In the Extension, select ESP-IDF option:
We will click the ‘sample_project’ under the get-started tab. Now click ‘Create project using template sample_project.’
You will get a notification that the project has been created. To open the project in a new window, click ‘Yes.’
This opens the project that we created inside the EXPLORER tab. There are several folders inside our project folder. This is the same for every project which you will create through ESP-IDF Explorer.
- First, let’s add the necessary header files for the BME680 libraries required for this project. Create a new folder called ‘components’ and Now add the bme680, esp_idf_lib_helpers and i2cdev folders in ‘components’ folder by copying from this link as listed below:
Now head over to the main.c file. The main folder contains the source code meaning the main.c file will be found here. Go to main > main.c and open it. Copy the c
ESP32 BME680 Web Server Code
#include <stdio.h>
#include <stdlib.h>
#include <string.h> //Requires by memset
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "esp_system.h"
#include "esp_spi_flash.h"
#include <esp_http_server.h>
#include "esp_wifi.h"
#include "esp_event.h"
#include "freertos/event_groups.h"
#include "esp_log.h"
#include "nvs_flash.h"
#include "esp_netif.h"
#include "driver/gpio.h"
#include <lwip/sockets.h>
#include <lwip/sys.h>
#include <lwip/api.h>
#include <lwip/netdb.h>
#include <bme680.h>
#define ESP_WIFI_SSID "HUAWEI-u67E"
#define ESP_WIFI_PASSWORD "4uF77R2n"
#define ESP_MAXIMUM_RETRY 5
#define BME680_I2C_ADDR 0x77
#define PORT 0
#define CONFIG_EXAMPLE_I2C_MASTER_SDA 21
#define CONFIG_EXAMPLE_I2C_MASTER_SCL 22
#ifndef APP_CPU_NUM
#define APP_CPU_NUM PRO_CPU_NUM
#endif
static const char *TAG = "esp32 webserver";
/* FreeRTOS event group to signal when we are connected*/
static EventGroupHandle_t s_wifi_event_group;
/* The event group allows multiple bits for each event, but we only care about two events:
* - we are connected to the AP with an IP
* - we failed to connect after the maximum amount of retries */
#define WIFI_CONNECTED_BIT BIT0
#define WIFI_FAIL_BIT BIT1
static int s_retry_num = 0;
int wifi_connect_status = 0;
bme680_t sensor;
bme680_values_float_t values;
uint32_t duration;
char html_page[] = "<!DOCTYPE HTML><html>\n"
"<head>\n"
" <title>ESP-IDF BME680 Web Server</title>\n"
" <meta http-equiv=\"refresh\" content=\"10\">\n"
" <meta name=\"viewport\" content=\"width=device-width, initial-scale=1\">\n"
" <link rel=\"stylesheet\" href=\"https://use.fontawesome.com/releases/v5.7.2/css/all.css\" integrity=\"sha384-fnmOCqbTlWIlj8LyTjo7mOUStjsKC4pOpQbqyi7RrhN7udi9RwhKkMHpvLbHG9Sr\" crossorigin=\"anonymous\">\n"
" <link rel=\"icon\" href=\"data:,\">\n"
" <style>\n"
" html {font-family: Arial; display: inline-block; text-align: center;}\n"
" p { font-size: 1.2rem;}\n"
" body { margin: 0;}\n"
" .topnav { overflow: hidden; background-color: #4B1D3F; color: white; font-size: 1.7rem; }\n"
" .content { padding: 20px; }\n"
" .card { background-color: white; box-shadow: 2px 2px 12px 1px rgba(140,140,140,.5); }\n"
" .cards { max-width: 700px; margin: 0 auto; display: grid; grid-gap: 2rem; grid-template-columns: repeat(auto-fit, minmax(300px, 1fr)); }\n"
" .reading { font-size: 2.8rem; }\n"
" .card.temperature { color: #0e7c7b; }\n"
" .card.humidity { color: #17bebb; }\n"
" .card.pressure { color: #3fca6b; }\n"
" .card.gas { color: #d62246; }\n"
" </style>\n"
"</head>\n"
"<body>\n"
" <div class=\"topnav\">\n"
" <h3>ESP-IDF BME680 WEB SERVER</h3>\n"
" </div>\n"
" <div class=\"content\">\n"
" <div class=\"cards\">\n"
" <div class=\"card temperature\">\n"
" <h4><i class=\"fas fa-thermometer-half\"></i> TEMPERATURE</h4><p><span class=\"reading\">%.2f °C</span></p>\n"
" </div>\n"
" <div class=\"card humidity\">\n"
" <h4><i class=\"fas fa-tint\"></i> HUMIDITY</h4><p><span class=\"reading\">%.2f</span> %</span></p>\n"
" </div>\n"
" <div class=\"card pressure\">\n"
" <h4><i class=\"fas fa-angle-double-down\"></i> PRESSURE</h4><p><span class=\"reading\">%.2fhPa</span></p>\n"
" </div>\n"
" <div class=\"card gas\">\n"
" <h4><i class=\"fas fa-wind\"></i> GAS</h4><p><span class=\"reading\">%.2f KΩ</span></p>\n"
" </div>\n"
" </div>\n"
" </div>\n"
"</body>\n"
"</html>";
void init_bme680(void)
{
memset(&sensor, 0, sizeof(bme680_t));
ESP_ERROR_CHECK(bme680_init_desc(&sensor, BME680_I2C_ADDR, PORT, CONFIG_EXAMPLE_I2C_MASTER_SDA, CONFIG_EXAMPLE_I2C_MASTER_SCL));
// init the sensor
ESP_ERROR_CHECK(bme680_init_sensor(&sensor));
// Changes the oversampling rates to 4x oversampling for temperature
// and 2x oversampling for humidity. Pressure measurement is skipped.
bme680_set_oversampling_rates(&sensor, BME680_OSR_4X, BME680_OSR_2X, BME680_OSR_2X);
// Change the IIR filter size for temperature and pressure to 7.
bme680_set_filter_size(&sensor, BME680_IIR_SIZE_7);
// Change the heater profile 0 to 200 degree Celsius for 100 ms.
bme680_set_heater_profile(&sensor, 0, 200, 100);
bme680_use_heater_profile(&sensor, 0);
// Set ambient temperature to 10 degree Celsius
bme680_set_ambient_temperature(&sensor, 10);
// as long as sensor configuration isn't changed, duration is constant
bme680_get_measurement_duration(&sensor, &duration);
}
void get_bme680_readings(void)
{
// trigger the sensor to start one TPHG measurement cycle
if (bme680_force_measurement(&sensor) == ESP_OK)
{
// passive waiting until measurement results are available
vTaskDelay(duration);
// get the results and do something with them
if (bme680_get_results_float(&sensor, &values) == ESP_OK)
printf("BME680 Sensor: %.2f °C, %.2f %%, %.2f hPa, %.2f KOhm\n",
values.temperature, values.humidity, values.pressure, values.gas_resistance);
}
}
static void event_handler(void *arg, esp_event_base_t event_base,
int32_t event_id, void *event_data)
{
if (event_base == WIFI_EVENT && event_id == WIFI_EVENT_STA_START)
{
esp_wifi_connect();
}
else if (event_base == WIFI_EVENT && event_id == WIFI_EVENT_STA_DISCONNECTED)
{
if (s_retry_num < ESP_MAXIMUM_RETRY)
{
esp_wifi_connect();
s_retry_num++;
ESP_LOGI(TAG, "retry to connect to the AP");
}
else
{
xEventGroupSetBits(s_wifi_event_group, WIFI_FAIL_BIT);
}
wifi_connect_status = 0;
ESP_LOGI(TAG, "connect to the AP fail");
}
else if (event_base == IP_EVENT && event_id == IP_EVENT_STA_GOT_IP)
{
ip_event_got_ip_t *event = (ip_event_got_ip_t *)event_data;
ESP_LOGI(TAG, "got ip:" IPSTR, IP2STR(&event->ip_info.ip));
s_retry_num = 0;
xEventGroupSetBits(s_wifi_event_group, WIFI_CONNECTED_BIT);
wifi_connect_status = 1;
}
}
void connect_wifi(void)
{
s_wifi_event_group = xEventGroupCreate();
ESP_ERROR_CHECK(esp_netif_init());
ESP_ERROR_CHECK(esp_event_loop_create_default());
esp_netif_create_default_wifi_sta();
wifi_init_config_t cfg = WIFI_INIT_CONFIG_DEFAULT();
ESP_ERROR_CHECK(esp_wifi_init(&cfg));
esp_event_handler_instance_t instance_any_id;
esp_event_handler_instance_t instance_got_ip;
ESP_ERROR_CHECK(esp_event_handler_instance_register(WIFI_EVENT,
ESP_EVENT_ANY_ID,
&event_handler,
NULL,
&instance_any_id));
ESP_ERROR_CHECK(esp_event_handler_instance_register(IP_EVENT,
IP_EVENT_STA_GOT_IP,
&event_handler,
NULL,
&instance_got_ip));
wifi_config_t wifi_config = {
.sta = {
.ssid = ESP_WIFI_SSID,
.password = ESP_WIFI_PASSWORD,
/* Setting a password implies station will connect to all security modes including WEP/WPA.
* However these modes are deprecated and not advisable to be used. Incase your Access point
* doesn't support WPA2, these mode can be enabled by commenting below line */
.threshold.authmode = WIFI_AUTH_WPA2_PSK,
},
};
ESP_ERROR_CHECK(esp_wifi_set_mode(WIFI_MODE_STA));
ESP_ERROR_CHECK(esp_wifi_set_config(WIFI_IF_STA, &wifi_config));
ESP_ERROR_CHECK(esp_wifi_start());
ESP_LOGI(TAG, "wifi_init_sta finished.");
/* Waiting until either the connection is established (WIFI_CONNECTED_BIT) or connection failed for the maximum
* number of re-tries (WIFI_FAIL_BIT). The bits are set by event_handler() (see above) */
EventBits_t bits = xEventGroupWaitBits(s_wifi_event_group,
WIFI_CONNECTED_BIT | WIFI_FAIL_BIT,
pdFALSE,
pdFALSE,
portMAX_DELAY);
/* xEventGroupWaitBits() returns the bits before the call returned, hence we can test which event actually
* happened. */
if (bits & WIFI_CONNECTED_BIT)
{
ESP_LOGI(TAG, "connected to ap SSID:%s password:%s",
ESP_WIFI_SSID, ESP_WIFI_PASSWORD);
}
else if (bits & WIFI_FAIL_BIT)
{
ESP_LOGI(TAG, "Failed to connect to SSID:%s, password:%s",
ESP_WIFI_SSID, ESP_WIFI_PASSWORD);
}
else
{
ESP_LOGE(TAG, "UNEXPECTED EVENT");
}
vEventGroupDelete(s_wifi_event_group);
}
esp_err_t send_web_page(httpd_req_t *req)
{
int response;
get_bme680_readings();
char response_data[sizeof(html_page) + 4];
memset(response_data, 0, sizeof(response_data));
sprintf(response_data, html_page, values.temperature, values.humidity, values.pressure, values.gas_resistance);
response = httpd_resp_send(req, response_data, HTTPD_RESP_USE_STRLEN);
return response;
}
esp_err_t get_req_handler(httpd_req_t *req)
{
return send_web_page(req);
}
httpd_uri_t uri_get = {
.uri = "/",
.method = HTTP_GET,
.handler = get_req_handler,
.user_ctx = NULL};
httpd_handle_t setup_server(void)
{
httpd_config_t config = HTTPD_DEFAULT_CONFIG();
httpd_handle_t server = NULL;
if (httpd_start(&server, &config) == ESP_OK)
{
httpd_register_uri_handler(server, &uri_get);
}
return server;
}
void app_main()
{
// Initialize NVS
esp_err_t ret = nvs_flash_init();
if (ret == ESP_ERR_NVS_NO_FREE_PAGES || ret == ESP_ERR_NVS_NEW_VERSION_FOUND)
{
ESP_ERROR_CHECK(nvs_flash_erase());
ret = nvs_flash_init();
}
ESP_ERROR_CHECK(ret);
ESP_ERROR_CHECK(i2cdev_init());
init_bme680();
ESP_LOGI(TAG, "ESP_WIFI_MODE_STA");
connect_wifi();
if (wifi_connect_status)
{
setup_server();
ESP_LOGI(TAG, "Web Server is up and running\n");
}
else
ESP_LOGI(TAG, "Failed to connected with Wi-Fi, check your network Credentials\n");
}How the Code Works?
Firstly, we will start by including the necessary libraries that includes the bme680.h for the sensor functionality, FreeRTOS libraries to generate delays, create tasks and event groups. The esp_http_server.h to setup an HTTP web server, esp_wifi.h to enable Wi-Fi connectivity, esp_event.h to monitor the Wi-Fi events, esp_log.h as the logging library, driver/gpio.h library for the digital output pins of ESP32 etc. Moreover, the driver/i2c.h library is used as it will enable the ESP32 to communicate with other I2C devices, in our case it is the BME680 sensor.
#include <stdio.h>
#include <stdlib.h>
#include <string.h> //Requires by memset
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "esp_system.h"
#include "esp_spi_flash.h"
#include <esp_http_server.h>
#include "esp_wifi.h"
#include "esp_event.h"
#include "freertos/event_groups.h"
#include "esp_log.h"
#include "nvs_flash.h"
#include "esp_netif.h"
#include "driver/gpio.h"
#include <lwip/sockets.h>
#include <lwip/sys.h>
#include <lwip/api.h>
#include <lwip/netdb.h>
#include <bme680.h>Next, we have defined the parameters for the Wi-Fi SSID and password. Specify your own network credentials to successfully connect your ESP32 board with the Wi-Fi network.
#define ESP_WIFI_SSID "YOUR_SSID"
#define ESP_WIFI_PASSWORD "YOUR_PASSWORD"We will define the maximum retry value to monitor the Wi-Fi connection. It is set as 5.
#define ESP_MAXIMUM_RETRY 5Next, we declare a variable ‘s_wifi-event_group’ to hold the created FreeRTOS event group. This FreeRTOS event group is used to signal when we are connected to Wi-Fi.
static EventGroupHandle_t s_wifi_event_group;Then we define two bits for the Wi-Fi events that are of importance to us. These include the bit for a successful Wi-Fi connection with an AP and another bit for a failed Wi-Fi connection with an AP after the maximum number of retries are over.
#define WIFI_CONNECTED_BIT BIT0
#define WIFI_FAIL_BIT BIT1Next, we have defined the SCL and SDA pins for I2C communication. Use these GPIO pins to connect the two devices together. You may change these pins as well.
#define SDA_PIN GPIO_NUM_21
#define SCL_PIN GPIO_NUM_22Inside code different tags become very useful when we want to log some information. ESP32-IDF have different level of log functions.
For example, the ESP_LOGI is used to log information for debugging. It takes in two arguments. The first argument is the tag and the second argument is a formatted string. Therefore this global variable will be useful while calling the ESP_LOGI() functions. Here, “esp32 webserver″ is the tag that will be used while logging.
static const char *TAG = "esp32 webserver";
HTML and CSS to build the Web Server
Then we have the array containing the HTML and CSS script for the HTML page. This includes the title of the web server and three cards to display each sensor reading along with an icon for each.
char html_page[] = "<!DOCTYPE HTML><html>\n"
"<head>\n"
" <title>ESP-IDF BME680 Web Server</title>\n"
" <meta http-equiv=\"refresh\" content=\"10\">\n"
" <meta name=\"viewport\" content=\"width=device-width, initial-scale=1\">\n"
" <link rel=\"stylesheet\" href=\"https://use.fontawesome.com/releases/v5.7.2/css/all.css\" integrity=\"sha384-fnmOCqbTlWIlj8LyTjo7mOUStjsKC4pOpQbqyi7RrhN7udi9RwhKkMHpvLbHG9Sr\" crossorigin=\"anonymous\">\n"
" <link rel=\"icon\" href=\"data:,\">\n"
" <style>\n"
" html {font-family: Arial; display: inline-block; text-align: center;}\n"
" p { font-size: 1.2rem;}\n"
" body { margin: 0;}\n"
" .topnav { overflow: hidden; background-color: #4B1D3F; color: white; font-size: 1.7rem; }\n"
" .content { padding: 20px; }\n"
" .card { background-color: white; box-shadow: 2px 2px 12px 1px rgba(140,140,140,.5); }\n"
" .cards { max-width: 700px; margin: 0 auto; display: grid; grid-gap: 2rem; grid-template-columns: repeat(auto-fit, minmax(300px, 1fr)); }\n"
" .reading { font-size: 2.8rem; }\n"
" .card.temperature { color: #0e7c7b; }\n"
" .card.humidity { color: #17bebb; }\n"
" .card.pressure { color: #3fca6b; }\n"
" .card.gas { color: #d62246; }\n"
" </style>\n"
"</head>\n"
"<body>\n"
" <div class=\"topnav\">\n"
" <h3>ESP-IDF BME680 WEB SERVER</h3>\n"
" </div>\n"
" <div class=\"content\">\n"
" <div class=\"cards\">\n"
" <div class=\"card temperature\">\n"
" <h4><i class=\"fas fa-thermometer-half\"></i> TEMPERATURE</h4><p><span class=\"reading\">%.2f °C</span></p>\n"
" </div>\n"
" <div class=\"card humidity\">\n"
" <h4><i class=\"fas fa-tint\"></i> HUMIDITY</h4><p><span class=\"reading\">%.2f</span> %</span></p>\n"
" </div>\n"
" <div class=\"card pressure\">\n"
" <h4><i class=\"fas fa-angle-double-down\"></i> PRESSURE</h4><p><span class=\"reading\">%.2fhPa</span></p>\n"
" </div>\n"
" <div class=\"card gas\">\n"
" <h4><i class=\"fas fa-wind\"></i> GAS</h4><p><span class=\"reading\">%.2f KΩ</span></p>\n"
" </div>\n"
" </div>\n"
" </div>\n"
"</body>\n"
"</html>";
The HTML code is specified with in the <html> </html> tags. Inside the <style> </style> tags, we specify the styling of the web page. This includes the font family, font size, positioning of the text, size and color for the cards etc.
We start off with the title of the web page. It is placed inside the <title> </title> tags. In our case, we have set the title of our web page as “ESP-IDF BME680 Web Server.” This will be displayed in the title bar of the browser.
<title>ESP-IDF BME680 Web Server</title>The following meta tag will enable our web server to be viewed on different devices.
" <meta name=\"viewport\" content=\"width=device-width, initial-scale=1\">\n"As we mentioned before, we want to add an icon of temperature, humidity and pressure inside the cards. Hence, the following link tag will acquire the icons from fontawesome.
" <link rel=\"stylesheet\" href=\"https://use.fontawesome.com/releases/v5.7.2/css/all.css\" integrity=\"sha384-fnmOCqbTlWIlj8LyTjo7mOUStjsKC4pOpQbqyi7RrhN7udi9RwhKkMHpvLbHG9Sr\" crossorigin=\"anonymous\">\n"As you may note, the font family of all the text is set as Arial and it is aligned in the center of the web page. The color and font size of the topnav is also set. We have three cards on our web page for each of the sensor reading. The overall styling of the cards along with the color of each individual reading is also set. We set size and color of the title of the card, along with the general styling of the card that includes its background color, box shadow etc.
<style>\n"
" html {font-family: Arial; display: inline-block; text-align: center;}\n"
" p { font-size: 1.2rem;}\n"
" body { margin: 0;}\n"
" .topnav { overflow: hidden; background-color: #4B1D3F; color: white; font-size: 1.7rem; }\n"
" .content { padding: 20px; }\n"
" .card { background-color: white; box-shadow: 2px 2px 12px 1px rgba(140,140,140,.5); }\n"
" .cards { max-width: 700px; margin: 0 auto; display: grid; grid-gap: 2rem; grid-template-columns: repeat(auto-fit, minmax(300px, 1fr)); }\n"
" .reading { font-size: 2.8rem; }\n"
" .card.temperature { color: #0e7c7b; }\n"
" .card.humidity { color: #17bebb; }\n"
" .card.pressure { color: #3fca6b; }\n"
" .card.gas { color: #d62246; }\n"
" </style>\n"Inside the <body> </body> tags, the heading, paragraphs and the cards will be included.
<body>\n"
" <div class=\"topnav\">\n"
" <h3>ESP-IDF BME680 WEB SERVER</h3>\n"
" </div>\n"
" <div class=\"content\">\n"
" <div class=\"cards\">\n"
" <div class=\"card temperature\">\n"
" <h4><i class=\"fas fa-thermometer-half\"></i> TEMPERATURE</h4><p><span class=\"reading\">%.2f °C</span></p>\n"
" </div>\n"
" <div class=\"card humidity\">\n"
" <h4><i class=\"fas fa-tint\"></i> HUMIDITY</h4><p><span class=\"reading\">%.2f</span> %</span></p>\n"
" </div>\n"
" <div class=\"card pressure\">\n"
" <h4><i class=\"fas fa-angle-double-down\"></i> PRESSURE</h4><p><span class=\"reading\">%.2fhPa</span></p>\n"
" </div>\n"
" <div class=\"card gas\">\n"
" <h4><i class=\"fas fa-wind\"></i> GAS</h4><p><span class=\"reading\">%.2f KΩ</span></p>\n"
" </div>\n"
" </div>\n"
" </div>\n"
"</body>\n"The heading of our web server is “ESP-IDF BME680 WEB SERVER” which is placed inside the <h3> </h3> tags.
<h3>ESP-IDF BME680 WEB SERVER</h3>Then we have the four cards that will display the temperature, humidity, pressure and gas readings, respectively. All of the sensor readings are referenced to the class ‘reading’. Each card has its icon followed by the title and the reading at the bottom along with the unit.
<body>\n"
" <div class=\"topnav\">\n"
" <h3>ESP-IDF BME680 WEB SERVER</h3>\n"
" </div>\n"
" <div class=\"content\">\n"
" <div class=\"cards\">\n"
" <div class=\"card temperature\">\n"
" <h4><i class=\"fas fa-thermometer-half\"></i> TEMPERATURE</h4><p><span class=\"reading\">%.2f °C</span></p>\n"
" </div>\n"
" <div class=\"card humidity\">\n"
" <h4><i class=\"fas fa-tint\"></i> HUMIDITY</h4><p><span class=\"reading\">%.2f</span> %</span></p>\n"
" </div>\n"
" <div class=\"card pressure\">\n"
" <h4><i class=\"fas fa-angle-double-down\"></i> PRESSURE</h4><p><span class=\"reading\">%.2fhPa</span></p>\n"
" </div>\n"
" <div class=\"card gas\">\n"
" <h4><i class=\"fas fa-wind\"></i> GAS</h4><p><span class=\"reading\">%.2f KΩ</span></p>\n"
" </div>\n"
" </div>\n"
" </div>\n"
"</body>\n"Below is the code for the line which displays the temperature readings, along with the units and thermometer icon.
<h4><i class=\"fas fa-thermometer-half\"></i> TEMPERATURE</h4><p><span class=\"reading\">%.2f°C</span></p>Reading BME680 Sensor Readings
These lines define the address of BME680 which 0x77, I2C port and ESP32 I2C pin numbers which 21 (SDA) and 22(SCL).
#define BME680_I2C_ADDR 0x77
#define PORT 0
#define CONFIG_EXAMPLE_I2C_MASTER_SDA 21
#define CONFIG_EXAMPLE_I2C_MASTER_SCL 22Initialize the i2c library and it should be called before calling any bme680 esp-idf library function.
ESP_ERROR_CHECK(i2cdev_init());BME680 Initialization Function
init_bme680() task initialize BME680 sensor, defines I2C port to which sensor is connected, sets sampling rates for temperature, humidity, pressure and gas readings, set filers size for temperature and pressure, sets the measurement duration, etc.
void init_bme680(void)
{
memset(&sensor, 0, sizeof(bme680_t));
ESP_ERROR_CHECK(bme680_init_desc(&sensor, BME680_I2C_ADDR, PORT, CONFIG_EXAMPLE_I2C_MASTER_SDA, CONFIG_EXAMPLE_I2C_MASTER_SCL));
// init the sensor
ESP_ERROR_CHECK(bme680_init_sensor(&sensor));
// Changes the oversampling rates to 4x oversampling for temperature
// and 2x oversampling for humidity. Pressure measurement is skipped.
bme680_set_oversampling_rates(&sensor, BME680_OSR_4X, BME680_OSR_2X, BME680_OSR_2X);
// Change the IIR filter size for temperature and pressure to 7.
bme680_set_filter_size(&sensor, BME680_IIR_SIZE_7);
// Change the heater profile 0 to 200 degree Celsius for 100 ms.
bme680_set_heater_profile(&sensor, 0, 200, 100);
bme680_use_heater_profile(&sensor, 0);
// Set ambient temperature to 10 degree Celsius
bme680_set_ambient_temperature(&sensor, 10);
// as long as sensor configuration isn't changed, duration is constant
bme680_get_measurement_duration(&sensor, &duration);
}Now let’s see function of each line one by one.
Here we create an instance of bme680_t struct which is used to configure and initialize sensor. After that initialize all members of sensor struct to zero with memset.
bme680_t sensor;
memset(&sensor, 0, sizeof(bme680_t));
typedef struct
{
i2c_dev_t i2c_dev; //!< I2C device descriptor
bool meas_started; //!< Indicates whether measurement started
uint8_t meas_status; //!< Last sensor status (for internal use only)
bme680_settings_t settings; //!< Sensor settings
bme680_calib_data_t calib_data; //!< Calibration data of the sensor
} bme680_t; bme680_init_desc() function initialize bme680 device descriptor by passing sensor struct, BME680 I2C address, ESP32 I2C pin numbers.
ESP_ERROR_CHECK(bme680_init_desc(&sensor, BME680_I2C_ADDR, PORT, CONFIG_EXAMPLE_I2C_MASTER_SDA, CONFIG_EXAMPLE_I2C_MASTER_SCL));
bme680_init_sensor() method initialize a BME680 sensor device data structure, probes the sensor, soft resets the sensor, and configures the sensor with the the following default settings:
- Oversampling rate for temperature, pressure, humidity = osr_1x
- Filter size for pressure and temperature = iir_size 3
- Heater profile 0 with 320 degree C and 150 ms duration
ESP_ERROR_CHECK(bme680_init_sensor(&sensor));
bme680_set_oversampling_rates() function set the oversampling rates for measurements of temperature, humidity, pressure and gas. With this function, we can set individual sampling rates for temperature, pressure and humidity. The bme680_init_desc() function sets the default sampling rates to 1x. But we can change them with this function. The possible oversampling rates are 1x (default), 2x, 4x, 8x, 16x.
bme680_set_oversampling_rates(&sensor, BME680_OSR_4X, BME680_OSR_2X, BME680_OSR_2X);
bme680_set_filter_size() define the size of IRR filers because BME680 has an internal IRR filter which can be used to minimize effect of short-term changes in sensor output values that might be caused by external disturbances. IRR filer adjust the reduce the output bandwidth of sensor.
bme680_set_filter_size(&sensor, BME680_IIR_SIZE_7);
The BME680 sensor have a built-in header for the gas measurement and it supports up to 10 heater profiles. Each profile consists of a temperature set-point (the target temperature) and a heating duration. This functions set the heater profile. The input arguments are sensor descriptor struct, heater profile, target temperature and heating duration. The bme680_set_heater_profile() function activate gas measurement with a given heater profile
bme680_set_heater_profile(&sensor, 0, 200, 100);
bme680_use_heater_profile(&sensor, 0);The bme680_set_ambient_temperature() function set the ambient temperature for heater resistance calculation. Because heater resistance calculation algorithm takes into account the ambient temperature of the sensor.
bme680_set_ambient_temperature(&sensor, 10);
bme680_get_measurement_duration() function determine the measurement duration from BME680 in terms of RTOS ticks.
uint32_t duration;
bme680_get_measurement_duration(&sensor, &duration);BME680 Sensor Data Read Function
The get_bme680_readings() functions reads sensor readings and populate them into ‘values’ struct of type bme680_values_float_t.
This bme680_values_float_t struct will populate with sensor values when we call bme680_get_results_float() function to get temperature, humidity, pressure and gas data from the sensor.
typedef struct
{
float temperature; //!< temperature in degree C (Invalid value -327.68)
float pressure; //!< barometric pressure in hPascal (Invalid value 0.0)
float humidity; //!< relative humidity in % (Invalid value 0.0)
float gas_resistance; //!< gas resistance in Ohm (Invalid value 0.0)
} bme680_values_float_t; bme680_values_float_t values;Inside this function, we call bme680_get_results_float() function to get BME680 sensor readings and store them to struct ‘values’. This struct is defined as a global struct and we will use it http response handler to send sensor values to web pages.
void get_bme680_readings(void)
{
// trigger the sensor to start one TPHG measurement cycle
if (bme680_force_measurement(&sensor) == ESP_OK)
{
// passive waiting until measurement results are available
vTaskDelay(duration);
// get the results and do something with them
if (bme680_get_results_float(&sensor, &values) == ESP_OK)
printf("BME680 Sensor: %.2f °C, %.2f %%, %.2f hPa, %.2f KOhm\n",
values.temperature, values.humidity, values.pressure, values.gas_resistance);
}
}Wi-Fi Connection and Status Monitoring
event_handler()
Then we have the event_handler() function which handles the Wi-Fi events. This acts as a callback function when either Wi-Fi event or IP event occurs.
The IP event occurs when the ESP32 board connects with our access point and the router assigns an IP address to it. IP events can be one of the following types. But here we are using only IP_EVENT_STA_GOT_IP.
/** IP event declarations */
typedef enum {
IP_EVENT_STA_GOT_IP, /*!< station got IP from connected AP */
IP_EVENT_STA_LOST_IP, /*!< station lost IP and the IP is reset to 0 */
IP_EVENT_AP_STAIPASSIGNED, /*!< soft-AP assign an IP to a connected station */
IP_EVENT_GOT_IP6, /*!< station or ap or ethernet interface v6IP addr is preferred */
IP_EVENT_ETH_GOT_IP, /*!< ethernet got IP from connected AP */
IP_EVENT_ETH_LOST_IP, /*!< ethernet lost IP and the IP is reset to 0 */
IP_EVENT_PPP_GOT_IP, /*!< PPP interface got IP */
IP_EVENT_PPP_LOST_IP, /*!< PPP interface lost IP */
} ip_event_t;Firstly, when the Wi-Fi events (WIFI_EVENT and WIFI_EVENT_STA_START) occur, we connect the ESP32 with the AP. We use the function esp_wifi_connect() to connect the board with the AP.
If the ESP32 board is unable to connect to an AP within the maximum number of retries set, then it again tries to connect with the AP and logs “retry to connect to the AP”. However, if the ESP32 is unable to establish connection with the AP after the maximum number of retries are over, then it logs “connect to the AP fail” and sets the WIFI_FAIL_BIT. Now, if the ESP32 board is able to successfully connect with an AP, then it suggests that both the IP events (IP_EVENT and IP_EVENT_STA_GOT_IP) occurred. In this case, it prints the ip address as an output. Moreover, it also sets the WIFI_CONNECTED_BIT.
static void event_handler(void *arg, esp_event_base_t event_base,
int32_t event_id, void *event_data)
{
if (event_base == WIFI_EVENT && event_id == WIFI_EVENT_STA_START)
{
esp_wifi_connect();
}
else if (event_base == WIFI_EVENT && event_id == WIFI_EVENT_STA_DISCONNECTED)
{
if (s_retry_num < ESP_MAXIMUM_RETRY)
{
esp_wifi_connect();
s_retry_num++;
ESP_LOGI(TAG, "retry to connect to the AP");
}
else
{
xEventGroupSetBits(s_wifi_event_group, WIFI_FAIL_BIT);
}
wifi_connect_status = 0;
ESP_LOGI(TAG, "connect to the AP fail");
}
else if (event_base == IP_EVENT && event_id == IP_EVENT_STA_GOT_IP)
{
ip_event_got_ip_t *event = (ip_event_got_ip_t *)event_data;
ESP_LOGI(TAG, "got ip:" IPSTR, IP2STR(&event->ip_info.ip));
s_retry_num = 0;
xEventGroupSetBits(s_wifi_event_group, WIFI_CONNECTED_BIT);
wifi_connect_status = 1;
}
}
connect_wifi()
The connect_wifi() function will be called inside the app_main() function to initialize Wi-Fi in station mode for ESP32.
void connect_wifi(void)
{
s_wifi_event_group = xEventGroupCreate();
ESP_ERROR_CHECK(esp_netif_init());
ESP_ERROR_CHECK(esp_event_loop_create_default());
esp_netif_create_default_wifi_sta();
wifi_init_config_t cfg = WIFI_INIT_CONFIG_DEFAULT();
ESP_ERROR_CHECK(esp_wifi_init(&cfg));
esp_event_handler_instance_t instance_any_id;
esp_event_handler_instance_t instance_got_ip;
ESP_ERROR_CHECK(esp_event_handler_instance_register(WIFI_EVENT,
ESP_EVENT_ANY_ID,
&event_handler,
NULL,
&instance_any_id));
ESP_ERROR_CHECK(esp_event_handler_instance_register(IP_EVENT,
IP_EVENT_STA_GOT_IP,
&event_handler,
NULL,
&instance_got_ip));
wifi_config_t wifi_config = {
.sta = {
.ssid = ESP_WIFI_SSID,
.password = ESP_WIFI_PASSWORD,
/* Setting a password implies station will connect to all security modes including WEP/WPA.
* However these modes are deprecated and not advisable to be used. Incase your Access point
* doesn't support WPA2, these mode can be enabled by commenting below line */
.threshold.authmode = WIFI_AUTH_WPA2_PSK,
},
};
ESP_ERROR_CHECK(esp_wifi_set_mode(WIFI_MODE_STA));
ESP_ERROR_CHECK(esp_wifi_set_config(WIFI_IF_STA, &wifi_config));
ESP_ERROR_CHECK(esp_wifi_start());
ESP_LOGI(TAG, "wifi_init_sta finished.");
/* Waiting until either the connection is established (WIFI_CONNECTED_BIT) or connection failed for the maximum
* number of re-tries (WIFI_FAIL_BIT). The bits are set by event_handler() (see above) */
EventBits_t bits = xEventGroupWaitBits(s_wifi_event_group,
WIFI_CONNECTED_BIT | WIFI_FAIL_BIT,
pdFALSE,
pdFALSE,
portMAX_DELAY);
/* xEventGroupWaitBits() returns the bits before the call returned, hence we can test which event actually
* happened. */
if (bits & WIFI_CONNECTED_BIT)
{
ESP_LOGI(TAG, "connected to ap SSID:%s password:%s",
ESP_WIFI_SSID, ESP_WIFI_PASSWORD);
}
else if (bits & WIFI_FAIL_BIT)
{
ESP_LOGI(TAG, "Failed to connect to SSID:%s, password:%s",
ESP_WIFI_SSID, ESP_WIFI_PASSWORD);
}
else
{
ESP_LOGE(TAG, "UNEXPECTED EVENT");
}
vEventGroupDelete(s_wifi_event_group);
}We start off by creating a FreeRTOS event group to monitor the connection. This returns a handle to the event group.
s_wifi_event_group = xEventGroupCreate();The ESP-IDF provides a useful macro called ESP_ERROR_CHECK() that will be used to check whether an error occurred or not. If the function that we pass inside it does not return ESP_OK, then we assert and log the line.
Here we are initializing lwIP through the function esp_netif_init() and create an IwIP task which is also known as a TCP/IP task. lwIP is a TCP/IP library stack provided by ESP-IDF that is used to perform various protocols such as TCP, UDP, DHCP etc.
ESP_ERROR_CHECK(esp_netif_init());Next, we create a default event loop which enables the system events to be sent to the event task.
ESP_ERROR_CHECK(esp_event_loop_create_default());Moreover, the following line is used for Wi-Fi default initialization for station mode. This API is used to initialize as well as register event handlers for the default interface which is station in our case. It creates a network interface instance binding Wi-Fi driver and TCP/IP stack. When a station is in the process of connecting to an AP, various processes automatically get handled through this function.
esp_netif_create_default_wifi_sta();Then we initialize the Wi-Fi allocate resource for the Wi-Fi driver. It is responsible for initiating the Wi-Fi task. It takes in a single parameter cfg which is a pointer to the already initialized Wi-Fi configuration structure which is set to WIFI_INIT_CONFIG_DEFAULT() so that the initialization of the configuration is at default values. Here wifi_init_config_t is a structure that denotes the Wi-Fi stack configuration parameters that are passed inside the esp_wifi_init() function.
wifi_init_config_t cfg = WIFI_INIT_CONFIG_DEFAULT();
ESP_ERROR_CHECK(esp_wifi_init(&cfg));Next, we create two event handlers called ‘instance_any_id’ for all Wi-Fi events and ‘instance_any_ip’ for when the station obtains the IP.
esp_event_handler_instance_t instance_any_id;
esp_event_handler_instance_t instance_got_ip;Next, we have two registers for the event handler instances that we set up. This way the application task can register for a callback that can listen for events for Wi-Fi and TCP/IP. The first event is ‘ESP_EVENT_ANY_ID‘ and the second event is ‘IP_EVENT_STA_GOT_IP.’ Therefore it will listen to all Wi-Fi events (ESP_EVENT_ANY_ID) and an IP event when the station got its IP address (IP_EVENT_STA_GOT_IP). Hence, the callback event_handler function will be called if any of these two events occur.
ESP_ERROR_CHECK(esp_event_handler_instance_register(WIFI_EVENT,
ESP_EVENT_ANY_ID,
&event_handler,
NULL,
&instance_any_id));
ESP_ERROR_CHECK(esp_event_handler_instance_register(IP_EVENT,
IP_EVENT_STA_GOT_IP,
&event_handler,
NULL,
&instance_got_ip));Other wifi events which we can use in our code are:
typedef enum {
WIFI_EVENT_STA_CONNECTED, /**< ESP32 station connected to AP */
WIFI_EVENT_STA_DISCONNECTED, /**< ESP32 station disconnected from AP */
WIFI_EVENT_AP_START, /**< ESP32 soft-AP start */
WIFI_EVENT_AP_STOP, /**< ESP32 soft-AP stop */
} mdns_used_event_t;
In this part, we set up the SSID and password of the network we want our ESP32 to connect with, as well as assign the security setting.
wifi_config_t wifi_config = {
.sta = {
.ssid = ESP_WIFI_SSID,
.password = ESP_WIFI_PASSWORD,
/* Setting a password implies station will connect to all security modes including WEP/WPA.
* However these modes are deprecated and not advisable to be used. Incase your Access point
* doesn't support WPA2, these mode can be enabled by commenting below line */
.threshold.authmode = WIFI_AUTH_WPA2_PSK,
},
};Moreover, we set Wi-Fi mode as station. To set the Wi-Fi mode as station, we use the function esp_wifi_set_mode() and pass the WiFI_MODE_STA as a parameter inside it.
ESP_ERROR_CHECK(esp_wifi_set_mode(WIFI_MODE_STA) );Then we assign our network’s SSID and password. This way the Wi-Fi driver gets configured with the AP network credentials and Wi-Fi mode. Then, we start the Wi-Fi connection at our assigned configuration.
ESP_ERROR_CHECK(esp_wifi_set_config(WIFI_IF_STA, &wifi_config) );
ESP_ERROR_CHECK(esp_wifi_start() );At this point the information log prints “wifi_init_sta finished.” We are done with the process of initializing the Wi-Fi in station mode.
ESP_LOGI(TAG, "wifi_init_sta finished.");Next the application moves to a blocked state whereby it waits for either of the bits in the event group to be set. This happens after the Wi-Fi is initialized and started. The application remains in the blocked state until either the Wi-Fi gets connected which is monitored by WIFI_CONNECTED_BIT or the W-Fi fails to connect within the maximum number of retries which is monitored by WIFI_FAIL_BIT.
Now if the event_handler() function sets the WIFI_CONNECTED_BIT which suggests that the ESP32 was able to successfully connect with an AP, then the informational log will print that it got connected to the SSID and password of the specified AP. If on the other hand, the event_handler() function sets the WIFI_FAIL_BIT which suggests that the ESP32 was not able to connected to the AP even after the maximum number of retries have been reached, then the informational log will print that it failed to connect to the SSID and password of the specified AP.
EventBits_t bits = xEventGroupWaitBits(s_wifi_event_group,
WIFI_CONNECTED_BIT | WIFI_FAIL_BIT,
pdFALSE,
pdFALSE,
portMAX_DELAY);
if (bits & WIFI_CONNECTED_BIT)
{
ESP_LOGI(TAG, "connected to ap SSID:%s password:%s",
ESP_WIFI_SSID, ESP_WIFI_PASSWORD);
}
else if (bits & WIFI_FAIL_BIT)
{
ESP_LOGI(TAG, "Failed to connect to SSID:%s, password:%s",
ESP_WIFI_SSID, ESP_WIFI_PASSWORD);
}
else
{
ESP_LOGE(TAG, "UNEXPECTED EVENT");
}
Moreover, we delete the event group ‘s_wifi_event_group’ using the vEventGroupDelete() function. It was created before by using a call to xEventGroupCreate().
vEventGroupDelete(s_wifi_event_group);ESP32 ESP32-IDF HTTP Requests Handlers
The send_web_page() function is responsible for sending a complete HTTP response by calling httpd_resp_send() function. The httpd_resp_send() API takes in three parameters. The first parameter is the request which is being responded to. The second parameter is the buffer from where the context has to be obtained. The third parameter is the length of the buffer. In the send_web_page() function, the HTTP response consists of the temperature, humidity and pressure readings that were acquired in the function get_bme680_readings().
esp_err_t send_web_page(httpd_req_t *req)
{
int response;
get_bme680_readings();
char response_data[sizeof(html_page) + 4];
memset(response_data, 0, sizeof(response_data));
sprintf(response_data, html_page, values.temperature, values.humidity, values.pressure, values.gas_resistance);
response = httpd_resp_send(req, response_data, HTTPD_RESP_USE_STRLEN);
return response;
}We have the uri-get handler structure shown below. Its chosen method is HTTP_GET, URL is “/” and the handler for this is get_req_handler which returns the send_web_page() response.
esp_err_t get_req_handler(httpd_req_t *req)
{
return send_web_page(req);
}
httpd_uri_t uri_get = {
.uri = "/",
.method = HTTP_GET,
.handler = get_req_handler,
.user_ctx = NULL};The following function will start the HTTP web server and return server which is the http handle.
httpd_handle_t setup_server(void)
{
httpd_config_t config = HTTPD_DEFAULT_CONFIG();
httpd_handle_t server = NULL;
if (httpd_start(&server, &config) == ESP_OK)
{
httpd_register_uri_handler(server, &uri_get);
}
return server;
}It starts by defining the default configuration and sets an empty handle to http server handle. It is set as NULL.
The httpd_start() function starts the httpd server. It takes in two parameters. Configuration for new instance of the server and handle to the instance of the server. If the instance was successfully created, which means this function returned ESP_OK then we will register the URI handlers. It takes in two parameters. The first parameter is the handle to HTTPD server instance which is ‘server’ in this case. The second parameter is the pointer to the handler that we what to register which is uri_get.
app_main()
Inside the app_main() function, first NVS is initialized by calling the nvs_flash_init() function. Then we will check if the NVS partition does not contain any empty pages or if it contains data in a format which is different from the current version of code. If any of these condition is true then we will erase the NVS flash using nvs_flash_erase() and initialize it again.
// Initialize NVS
esp_err_t ret = nvs_flash_init();
if (ret == ESP_ERR_NVS_NO_FREE_PAGES || ret == ESP_ERR_NVS_NEW_VERSION_FOUND)
{
ESP_ERROR_CHECK(nvs_flash_erase());
ret = nvs_flash_init();
}
ESP_ERROR_CHECK(ret);Then we will call the function, i2cdev_init() to initialize the I2C and call init_bme680() function.
ESP_ERROR_CHECK(i2cdev_init());
init_bme680();Then we will print “ESP_WIFI_MODE_STA” in the terminal and call the connect_wifi() function to connect the Wi-Fi for station mode.
ESP_LOGI(TAG, "ESP_WIFI_MODE_STA");
connect_wifi();If the ESP32 successfully connects with the Wi-Fi network, then the setup_server() function is called to start the HTTP web server and the terminal prints the message saying that the BME680 web server is running. Otherwise, the ESP-IDF terminal prints a network failure message.
if (wifi_connect_status)
{
setup_server();
ESP_LOGI(TAG, "Web Server is up and running\n");
}
else
ESP_LOGI(TAG, "Failed to connected with Wi-Fi, check your network Credentials\n");Compiling the Sketch
To flash your chip, type the following command in the serial terminal. Remember to replace the COM port with the one through which your board is connected.
idf.py -p COMX flash monitorAfter the code flashes successfully, you can view all the informational logs. First, the station Wi-Fi is initialized. Then we can view the esp_netif_handlers which includes the IP, mask, and gw addresses. Then we get the log “got IP” followed by the ip address. We will use this IP address to access the web server.
Open a new web browser and type the IP address that you obtained in the terminal, then press enter. The ESP32 BME680 web server will open up showing the temperature, pressure and humidity readings that update after every few seconds.
You may also like to read:
If you are using Arduino IDE instead of ESP-IDF, you can refer to these articles:
- ESP32 DHT11 and DHT22 Web Server using Arduino IDE
- ESP32 DS18B20 Temperature Sensor Web Server with Arduino IDE
- BME280 Web Server with ESP32 (Arduino IDE)
- BME680 Web Server with ESP32 ( Arduino IDE)
We are a team of experienced Embedded Software Developers with skills in developing Embedded Linux, RTOS, and IoT products from scratch to deployment with a demonstrated history of working in the embedded software industry. Contact us for your projects: admin@esp32tutorials.com