β οΈ Affiliate Disclosure: This post contains Amazon affiliate links. If you purchase through our links, we may earn a small commission at no extra cost to you. Every product below was checked against its live Amazon listing before publishing. Prices change often, so we don’t list them here. Tap any Buy Here button to see the current price on Amazon.
Maker Tool Buying Guide
π₯ Best Hot Glue Guns for Electronics Projects
Strain relief for wires, boards fixed inside enclosures, sensors tacked in place and loose connectors secured. Here are 7 glue guns and pens that do it cleanly, from precise mini guns to cordless and pro-grade picks.
β
7 Glue Guns Compared
β
Verified Amazon ASINs
β
Low vs High Temp Explained
β
Honest Pros & Cons
Hot glue is one of the most useful materials on an ESP32 bench. A dab on a JST or Dupont connector stops it working loose, a bead where a cable leaves a board gives it strain relief, and a few spots hold a dev board, sensor or LiPo cell inside a 3D printed or ABS enclosure without screws. It’s non-conductive, sets in seconds, and can usually be peeled off or released with a little isopropyl alcohol when you need to rework something.
The gun matters more than you might think. A small, precise nozzle puts glue exactly where you want it instead of across neighbouring pins, a low temperature setting is kinder to thin wire insulation and plastic parts, and a cordless or self-standing gun is much easier to use inside a crowded enclosure. This guide compares 7 picks from Gorilla, Surebonder, Ryobi, Stanley, Steinel and Bosch, each with a clear job.
π‘ Before you buy: Hot glue is for holding and insulating, not for heat sinking or permanent potting. Keep it off parts that get hot (regulators, motor drivers, LEDs at full power), never cover an ESP32’s PCB antenna with a thick blob, and check stick size: mini guns take about 7 mm sticks, full-size guns take 11 mm (7/16 inch) sticks, and they are not interchangeable.
β‘ Quick Comparison: All 7 Glue Guns
| Glue Gun | Type | Key Specs | Best For | Buy |
|---|
| π₯ Gorilla Dual Temp Mini | Corded mini | Low / high switch, 7 mm sticks | Best for Electronics | Buy Here β |
| π Surebonder CL-800F | Cordless / corded | 60 W, high temp, 11 mm sticks | Best Cordless Base Gun | Buy Here β |
| π Surebonder PRO2-100 | Corded full size | 100 W, 380Β°F, 11 mm sticks | Best Heavy Duty | Buy Here β |
| β‘ Ryobi P305 | 18V ONE+ cordless | Full size, tool only | Best Battery Powered | Buy Here β |
| π§ Stanley GR100 | Corded full size | DualMelt high / low | Best Dual Temp Full Size | Buy Here β |
| π Steinel Gluematic 3002 | Corded full size | 206Β°C, 16 g/min, 11 mm sticks | Premium Pick | Buy Here β |
| βοΈ Bosch Gluey | Cordless pen | 150Β°C, 7 mm x 20 mm sticks | Best Glue Pen | Buy Here β |
Specs come from the manufacturers, retailers and the live Amazon listings. Star scores below are our ratings.
π What Matters in a Glue Gun for Electronics
π‘οΈ
Temperature
Low temperature is gentler on thin insulation, foam and printed parts. High temperature bonds harder materials and holds better under warmth.
π―
Nozzle Precision
A long, narrow, insulated nozzle lets you place a small bead on one connector without flooding the pins next to it.
π
Stick Size
Mini guns use about 7 mm sticks for small jobs; full-size guns use 11 mm (7/16 inch) sticks and move far more glue.
π
Cordless Freedom
No cord to drag across the board makes it much easier to work inside an enclosure or on a mounted project.
π‘οΈ
Stand and Safety
A built-in stand, insulated nozzle and on/off switch matter on a crowded bench next to boards and cables.
π Detailed Reviews: The Top Two
π₯ BEST FOR ELECTRONICS
Gorilla Dual Temp Mini Hot Glue Gun Kit
β 4.7/5 Β· Our Rating Β· The Precise Bench Gun
Buy on Amazon β

For electronics, a mini gun is usually the right tool, and Gorilla’s is one of the best known. A switch selects low or high temperature: low for thin wire insulation, foam and printed parts, high when you need a stronger bond. The long insulated nozzle reaches into enclosures and lets you put a small bead on a single JST plug or the root of a sensor cable. It has an easy squeeze trigger, a rubber handle, a fold-up stand and a wide base so it doesn’t tip over on the bench. This kit includes 30 Gorilla mini sticks to get you started.
β
Pros- Low and high temperature
- Long precision nozzle
- Fold-up stand, wide base
- Sticks included
β Cons- Mini output is slow for big jobs
- Corded
π― Verdict: The best all-round glue gun for strain relief, securing connectors and mounting boards in enclosures.
π Check Price on Amazon β
π BEST CORDLESS BASE GUN
Surebonder CL-800F Cordless / Corded Glue Gun
β 4.6/5 Β· Our Rating Β· Lift It Off the Base
Buy on Amazon β

The CL-800F heats up on a small powered base, then you lift it off and use it with no cord for up to 2 minutes, which is exactly how long most enclosure jobs take. Put it back on the base to reheat, or plug the cord straight into the gun for continuous corded use. It’s a 60 W, high temperature, full-size gun, so it moves more glue than a mini and bonds harder materials like ABS, metal brackets and wood. That extra heat means you should be careful near thin insulation and printed parts.
β
Pros- No cord in the way
- Corded mode for long jobs
- 60 W full-size output
- Strong high-temp bonds
β Cons- High temp only
- Short cordless window
π― Verdict: The easiest way to glue inside an enclosure without a cord dragging across your board.
π Check Price on Amazon β
π§ Detailed Reviews: Full Size and Cordless
π BEST HEAVY DUTY Β· β 4.6/53. Surebonder PRO2-100 Professional Glue Gun
100 W Β· 380Β°F high temp Β· 7/16 inch sticks Β· about 2.5 lb of glue per hour Β· PTC heater Β· on/off switch
Buy Here β

When you build a lot of enclosures, mount panels or glue cable clips and brackets, the PRO2-100 keeps up. Its 100 W solid-state PTC heater holds a constant 380Β°F and pushes out about 2.5 lb of glue per hour, far more than any mini gun. A 4-finger trigger reduces hand fatigue, an on/off switch lets it stay plugged in between jobs, and the cord is double insulated. Optional nozzles, including a fine needle tip, are sold separately. It’s too much gun for tiny connector work.
β
Pros: High output; constant PTC temperature; on/off switch; optional nozzles.
β Cons: Overkill for small jobs; high temp only.
π― Verdict: The workhorse for frequent enclosure builds and larger mounting jobs.
β‘ BEST BATTERY POWERED Β· β 4.5/54. Ryobi P305 18V ONE+ Hot Glue Gun
18V ONE+ battery Β· full-size sticks Β· self-standing Β· includes 3 glue sticks Β· tool only
Buy Here β

If you already own Ryobi ONE+ tools, the P305 turns any 18V battery into a fully cordless full-size glue gun with no base and no time limit beyond the battery. That’s ideal for installing ESP32 sensors around the house, fixing cable runs behind furniture or working at an outdoor weather station. It’s self-standing and built for heavy duty gluing, and it ships with 3 general purpose sticks. The listing is tool only, so the battery and charger are extra.
β
Pros: Truly cordless; uses Ryobi 18V packs; stands on its own.
β Cons: Battery not included; bulky for fine work.
π― Verdict: The best pick for gluing jobs away from the bench if you’re on the Ryobi platform.
π§ BEST DUAL TEMP FULL SIZE Β· β 4.4/55. Stanley GR100 DualMelt Pro Glue Gun Kit
DualMelt high / low temperature Β· full-size gun Β· pro kit
Buy Here β

The GR100 gives you what the Surebonder full-size guns don’t: a DualMelt switch between high and low temperature in a full-size, pro-style gun. Use low for foam, thin insulation and printed parts, and high for wood, metal and ABS. It’s a good single gun if you want more output than a mini without giving up the gentler low setting. Stanley’s own pages list fewer detailed specs than Surebonder’s, so check the listing for the exact kit contents.
β
Pros: High and low temperature; full-size output.
β Cons: Fewer published specs; heavier than a mini.
π― Verdict: A versatile full-size gun when you need both temperature settings.
β Also Worth Considering
π PREMIUM PICK Β· β 4.7/5
6. Steinel Gluematic 3002
A German-engineered full-size gun with PTC heating, a melt temperature of 206Β°C and a delivery rate of 16 g/min. It takes 11 mm sticks and has interchangeable nozzles, including an optional 1.0 mm fine nozzle for precise dosing, which is handy for small electronics jobs. It draws 200 W while heating and about 45 W while working. Warm-up takes longer than budget guns. The listing includes 3 ULTRA power sticks.
Buy Here ββοΈ BEST GLUE PEN Β· β 4.3/5
7. Bosch Gluey Cordless Hot Glue Pen
A pen-shaped, fully cordless glue tool for the tiniest jobs. It runs on 2 rechargeable AA cells with a USB charger, heats up in about 60 seconds, works at 150Β°C and uses short 7 mm x 20 mm sticks at 2 g/min, with up to 60 sticks per charge. The kit includes 20 sticks. It’s great for tacking a wire or a small module in place, but the output is too low for anything bigger.
Buy Here βπ§© Which Glue Gun for Which ESP32 Job?
| ESP32 Job | Best Pick |
|---|
| Strain relief on JST, Dupont and sensor cables | Gorilla Dual Temp Mini (low temp) |
| Mounting a dev board or LiPo inside a 3D printed case | Gorilla Mini or Surebonder CL-800F |
| Tacking a single wire or tiny module | Bosch Gluey |
| Gluing cable clips, brackets and panels | Surebonder PRO2-100 or Steinel 3002 |
| Installing sensors around the house or outdoors | Ryobi P305 |
| One full-size gun for mixed materials | Stanley GR100 |
π Which One Should You Buy?
π§°
Your first glue gun
The Gorilla Dual Temp Mini: precise, low temp option, sticks included.
π
Hate cords on the bench
The Surebonder CL-800F, or the Ryobi P305 if you own Ryobi batteries.
π
You build lots of enclosures
The Surebonder PRO2-100 or the Steinel Gluematic 3002.
βοΈ
Only tiny touch-ups
The Bosch Gluey pen.
β Frequently Asked Questions
Is hot glue safe to use on circuit boards?
Yes, standard hot melt glue is non-conductive, so it’s widely used for strain relief and holding parts. Use the low temperature setting near thin insulation and plastic parts, keep it off components that run hot, and don’t bury the ESP32’s PCB antenna under a thick blob.
How do I remove hot glue from a board?
A few drops of isopropyl alcohol around the edge of the glue usually breaks its grip on the PCB so you can peel it off. Gentle warmth from a heat gun also softens it, but keep the heat away from sensitive parts.
Low temperature or high temperature glue?
Low temperature is gentler on wire insulation, foam and 3D printed parts. High temperature bonds harder materials more strongly and softens less in a warm enclosure. A dual temp gun like the Gorilla Mini or Stanley GR100 gives you both.
Can hot glue hold a board inside an enclosure?
For light boards and modules, yes. For anything that sees vibration, heat or repeated handling, use screws or standoffs and keep hot glue for cables and strain relief.
Can I use mini glue sticks in a full-size gun?
No. Mini guns take sticks of about 7 mm and full-size guns take 11 mm (7/16 inch) sticks. Buy sticks that match your gun.
π Final Verdict: Best Hot Glue Guns for Electronics
The right glue gun for each job:
π₯ Best for Electronics: Gorilla Dual Temp Mini
Buy Here βFor most ESP32 benches, the Gorilla Dual Temp Mini is the glue gun to buy first: its low setting and long nozzle are ideal for strain relief and securing connectors. Add the Surebonder CL-800F or Ryobi P305 if you want to work without a cord, and the Surebonder PRO2-100 or Steinel Gluematic 3002 if you build a lot of enclosures. Pair your glue gun with our guides to heat shrink tubing and heat guns, 3D printers for ESP32 enclosures, prototyping supplies and soldering accessories.
π¬ What do you use hot glue for in your ESP32 builds? Tell us in the comments below, and we’ll help you pick the right gun.
All Amazon links above use our affiliate tag (esp32tutorials-20). Purchasing through them supports esp32tutorials.com at no extra cost to you. Prices and availability change frequently, so always confirm the current price on Amazon before buying.
We are a team of experienced Embedded Software Developers with skills in developing Embedded Linux, RTOS, and IoT products from scratch to deployment with a demonstrated history of working in the embedded software industry. Contact us for your projects: admin@esp32tutorials.com